-
Posted by benjaminrivera20 on Nov 5th, 2009 at 10:59pm
Compressor won't start
I was testing my paint gun with just air then I turned it off. I tried to turn it back on but it wouldn't start. It just makes a humming noise for a few seconds then shuts off completely. I press the resetbutton but the same thing happens help
-
Posted by anattaway on Nov 2nd, 2009 at 4:14pm
cylinder head
cracked cylinder head, need replacement
-
Posted by paulbiggc on Nov 2nd, 2009 at 2:39pm
Transformer repair
I need to get the unit repaired, maybe new transformer. Were can I find this service. Harbor Freight does not offer repairs.
-
Posted by bobriverview on Oct 31st, 2009 at 10:36pm
need new electic compasitor
where to order parts
-
Posted by donraefie on Oct 29th, 2009 at 7:28pm
hex blade
cannot insert the hex blade into the blade holder
Chicago jigsaw 92772
-
Posted by antoniono on Oct 29th, 2009 at 3:07pm
Metal cutting band saw
drive gear striped
-
Posted by mjgadler on Oct 27th, 2009 at 6:59pm
4218 slide saw
The electrical switch broke and the saw failed in the power on position. I unplugged the saw, removed a few screws and examined the switch. I found that the switch is reverse wired, hot is common and the low side appears to be switched. A very strange setup, I would like to change this (hazardou…
-
Posted by flavasseur on Oct 20th, 2009 at 4:33pm
chicago 7" tile saw 40315
Am in need of a tile guide and angle guide.
-
Posted by lyndahollyfield on Oct 19th, 2009 at 10:11am
Need replacement battery charger
can't find battery charger
and looking for someplace to purchase one
-
Posted by smokey3206 on Oct 17th, 2009 at 6:21am
runs and then stops
This tool is about 3 years old and has not been used that often. I have put new brushes in it and added 1 1/4 oz of lithium grease. It still runs for a few seconds and then stops. Can it be a bad power switch? Or Could it be a bad capacitor or perhaps a bad variable speed control dial? It does n…
-
Posted by xpd2206 on Oct 16th, 2009 at 9:08am
proper loading of 18 guage nails
I just purchased a Chicago Electric 3-n-1 stapler/nailer. The stapler works super and cut the work time (stapling a pool table felt) in half. Included with the stapler was an ample supply of T-50 staples and some 18 guage nails. My question: How do you load the 18 gauge nails into the gun?
Th…
-
Posted by royandlinda on Oct 7th, 2009 at 3:17pm
uno mig flux wire welder
heat controler setings 1-2-3-4 need pitcure and price amount and part noumber
-
Posted by abcknox416 on Sep 29th, 2009 at 5:41pm
charger
want charge
-
Posted by softballdevils on Sep 28th, 2009 at 6:58pm
pressure swith
need a5, and on and off switch
model 42321
-
Posted by alver on Sep 28th, 2009 at 6:52pm
Don't work
When i hook it up to a battery and turn it on it will come on then go rite back off over & over again.
-
Posted by bgeraughty on Sep 25th, 2009 at 9:48pm
Where does hydrolic fluid go?
On page 12 of the manual, Figure E shows that there should be an oil fill/drain port located on the end of the unit. The unit looks nothing like the picture in the manual. Any idea where the hydrolic fluid goes?
-
Posted by quintaly on Sep 21st, 2009 at 10:39am
chicago electric rotary tumbler
i am searching information for the parts of the chicago electric rotary tumbler
item 46376
thanks for your help
-
Posted by quintaly on Sep 21st, 2009 at 10:38am
chicago electric rotary tumbler
i am searching information for the parts of the chicago electric rotary tumbler
item 46376
thanks for your help
-
Posted by lindashelton on Sep 16th, 2009 at 1:45pm
Parts
I need a wire feed for this welder
-
Posted by lindashelton on Sep 16th, 2009 at 1:45pm
Parts
I need a wire feed for this welder
-
Posted by ballen2266 on Aug 27th, 2009 at 8:35pm
busted line
line from manifold to the bottom of the tank busted. where can i get a replacement?
-
Posted by alwaysajg on Aug 26th, 2009 at 9:00pm
Drill Battery
The battery for my Model 40209 Cordless Drill has quit holding a charge. How can I buy a new battery for my drill?
-
Posted by mmcglamery on Aug 25th, 2009 at 9:07pm
Replacement Part
Need replacement "spreader" or "duck bill" 1/2 Ton Cap.
-
Posted by mmcglamery on Aug 25th, 2009 at 9:07pm
Replacement Part
Need replacement "spreader" or "duck bill" 1/2 Ton Cap.
-
Posted by osprey77 on Aug 21st, 2009 at 4:46pm
STARTS THEN STOPS, OIL LEAK
COMPRESSOR LEAKS OIL FROM WHAT MIGHT BE CASTING DEFECT IN COMPRESSOR CHAMBER. ALSO, AFTER NO USE FOR A COUPLE OF YEARS WHEN STARTS UP COMPRESSOR RUNS FOR ABOUT A SECOND AND THEN STOPS WITH A BUZZING SOUND. MANY THANKS
-
Posted by acdevilla on Aug 19th, 2009 at 8:44pm
air pressure not setting into lock
when lever is turned on, air pressure goes down even when power on. why?
-
Posted by ginron on Aug 18th, 2009 at 8:59pm
rubber diafram for on off switch hatbour freight 47065
i have a air compressor chicago pnuematic 47065 bought at harbour freight 47065 i need the rubberdiafram on the on off switch
-
Posted by jaxdragon47 on Aug 15th, 2009 at 12:20am
need trigger assembly
model#95156 gas powered by Pacific Hydrostar. i need new trigger assembly or just the trigger valve and pin. can't find any parts. JAX
-
Posted by jaxdragon47 on Aug 15th, 2009 at 12:08am
Pacific Hydrostar pressure washer
I'm looking for a parts list for this model. Mainly I need the trigger or just the trigger valve. Think you can help? JAX
-
Posted by garlandjones5 on Aug 14th, 2009 at 9:06pm
Pacific Hydrostar 6.5 HP 2800 PSI Pressure Washer
Trying to find a manual for this unit, model # 65078.
-
Posted by harbans on Aug 5th, 2009 at 7:50pm
compressor 47065
it will not start,soon i plug in lot of humming noise and after 4 or 5 sec. breaker trips.may be bad caps or bad winding. please help
thanks
-
Posted by cmdupier on Aug 5th, 2009 at 12:08am
model # 32206 or 32208 14" band saw
I need a lower blade guide assembly. Who can help?
-
Posted by rp4n on Jul 30th, 2009 at 10:06am
Drill Press Spindle Shaft
Does anyone know where I can find the spring clip(s)-if I am using the correct terminology-for the Spindle Shaft of a Central Machinery 38119 Drill Press?
-
Posted by alstam on Jul 28th, 2009 at 4:48pm
pressure switch diaphragm
The rubber diaphragm leaks on the pressure switch on my Central Pneumatics 40400 compressor. Where can I get a new one
-
Posted by mastcells on Jul 24th, 2009 at 8:28pm
pressure variation
I have never used a compressor before. I just bought a Central Pneumatic 40400. I wonder if the compressor will retain a steady pressure of about 90 psi for use with the Boschtich floor stappler. Does the motor slow down or shut off at a specific pressure set by the pressure regulator?
-
Posted by drcroley on Jul 14th, 2009 at 11:16pm
SPARE PARTS!
NEED AIR FILTER ASSEMBLY FOR 90385.
-
Posted by oldiejim on Jul 14th, 2009 at 5:07pm
Air Leak
I have an air leak and believe it is inside the air pressure switch but I don't have a manual that shows the internal workings or how to remove the cover to check inside.
-
Posted by hogwild_jones on Jun 27th, 2009 at 2:32pm
Manual
Seal on top of drive cyclinder is cracked and leaking. Need manual or part numbers for seal and gasket.
-
Posted by dcharle383 on Jun 27th, 2009 at 10:26am
pressure runs up then safety valve pops open
Pressure runs up then safety valve pops open as the pressure runs down to about 80psi valve closes and compressor starts back up.
-
Posted by chep42 on Jun 21st, 2009 at 12:54pm
battery charger
chicago cordless drill model 94434 i need a battery charger for this drill where can I get one
-
Posted by steven.gamble on Jun 20th, 2009 at 9:15pm
Need manual
The web site will not allow mw to download the requested file
-
Posted by csdean on Jun 20th, 2009 at 5:06pm
replacement part
I need a new housing for the air filter. #9411129 for the central Pneumatic 95386 air compressor
-
Posted by csdean on Jun 20th, 2009 at 5:06pm
replacement part
I need a new housing for the air filter. #9411129 for the central Pneumatic 95386 air compressor
-
Posted by showlow2u on Jun 15th, 2009 at 8:20pm
Help requested
Instruction manual very diffcult I do need digital photos or video to erect this.
1. does not state to drill own holes for foundation to the four plates part 16 , 17, and 2 parts 34,
which way is facing for part 10 the views are unclear in spec.
Tried and took apart waiting on your assista…
-
Posted by janflanagan on Jun 14th, 2009 at 8:14pm
no manual
the product # is not coming up and I purchased this 3 gallon oilless air compressor at HF in chicago. Please help we have no idea how to work it. It is red with a black top and round
-
Posted by googs2 on Jun 14th, 2009 at 3:42pm
repair pump
Looking for a seal kit and munual for a powerwasher with a Annovi Reverberi pump, XTV 3 6 18, 3GPM ,KW 2.7,1740 PSI,HP 3.5 ,3400 RPM
-
Posted by pamw77 on Jun 13th, 2009 at 7:57pm
Pressure switch
Want to buy replacement/
-
Posted by daw.ridakaw14 on Jun 11th, 2009 at 9:57pm
Did not get manual for Model#94724
What weight oil is used and where do you add it. I see a clear plastic cover by the cylinder head is that it
-
Posted by wlo on Jun 9th, 2009 at 1:06am
Central machinery 12x36" wood lathe tailstock
I'm missing some part(s) to make the tail stock tighten down to the lathe bed. the model # is T34706 10 variable speed. Where can I get them
-
Posted by nerolt on Jun 6th, 2009 at 2:05pm
Central Pneumatics Model 42321
I purchased this model used. I have the manual but there is no switch. Just a hole where it should be. What should I do now? Is there a replacement part available? Thanks Loren
-
Posted by jim on Jun 5th, 2009 at 5:01pm
Parts for 46935 Breaker Hammer
Price and availability
1 of #49
2 of #50
2 of #51
2 of #52
2 of #53
2 of #54
1 of #55
-
Posted by sinin2pleazu on Jun 4th, 2009 at 7:19am
need wire schematic
A while back someone attempted to sill my security cam. by yanking it. In doing so the cord from the cam broke just in-front of the phone jack connecter now all I'm left with is 4 wires....
1) white
2) blue
3) orange
4) yellow
Can you tell me what wire's go to power, video, mic. and grou…
-
Posted by tarz222 on May 25th, 2009 at 6:31pm
page 16 assembly instructions
wasn't included
-
Posted by roomkey on May 24th, 2009 at 5:30pm
Central Pneumatic compressor
The compressor will not go above 42 PSI no matter how long it runs. As there is no pressure regulator that I an adjust, what can I do?
-
Posted by donaldtroy9 on May 19th, 2009 at 10:31pm
3/4hppump
howtoremovetheitem 17 impeller for repair.i asked before
-
Posted by hpdshop5 on May 16th, 2009 at 9:22am
air
compressor will not build pressure
-
Posted by cbarney504 on May 12th, 2009 at 2:25am
pressure will not rise past 20 psi
Incomplete pressure,
When using the compressor it gets to about 20 psi and then a whisling noise starts and the pressure doesnt go any higher. I dont know the source of the leak.
-
Posted by loftonjrh on May 9th, 2009 at 12:56pm
47065 parts central pneumatic
I need the rubber disk on the botton of the on/off switch
-
Posted by donaldtroy9 on May 8th, 2009 at 4:14pm
3/4shallowwellpump
howtoremoveimpeller
-
Posted by williamofields on May 4th, 2009 at 11:20am
vents
what holds them in place. are there hinges or something else to hold them.
-
Posted by sandramccathy on May 3rd, 2009 at 11:01am
connection
The product stats that it can be connect to a monitor. but there is no instructions
-
Posted by sandramccathy on May 2nd, 2009 at 7:49pm
how to connect to a monitor
can this camera be connect to a pc monitor
-
Posted by db3607 on Apr 30th, 2009 at 6:01am
owners manual
Need a manual for this air compressor
-
Posted by jubi7 on Apr 27th, 2009 at 11:14pm
how touse tool for cutting off a1inch bolt and screw
how to use tool for cutting off a 1 inch bolt and screw.
-
Posted by brianmorrow1966 on Apr 24th, 2009 at 9:31pm
loading staples
how to load staples in the central pneumatic stapler/nailer gun
-
Posted by egasta on Apr 20th, 2009 at 11:41am
Moniter
I am in quest for a 4 way moniter are I wiil settle for a two window one .Please advise me if you got them.If not where can I purchase one. I am in need badly for this .
-
Posted by dosatsu_ryoku on Apr 18th, 2009 at 8:42pm
chicago eletric power tools
no manual
-
Posted by gmbatista on Apr 14th, 2009 at 7:05pm
trouble shoot
will not shut off
-
Posted by dlhbettie on Apr 10th, 2009 at 12:42am
chicago electric 18 volt cordless drill, model 95848
I need a charger. I also want to price the 18 volt battery.
-
Posted by hermansrus_ on Apr 8th, 2009 at 10:50am
air compressor
power switch does not work right. must compress and hold button to shut off.
-
Posted by euroman669 on Apr 4th, 2009 at 3:42pm
break-in smoke normal ?
Brandnew Chicago 03418. Trying to charge at 12VDC-10A 2 very dead and very big Duralast 12V Marine batteries in my motorhome. Battery cables disconnected, + and - clips on the anodes. The needle went off the scale to 0%, drawing max Amps. After a few minutes the charger started to smoke. Let it co…
-
Posted by tomg on Apr 3rd, 2009 at 3:59pm
Air Compressor Engine
I haved ruined the engine of the air compressor. What will a raplacement cost me?
-
Posted by ntv000 on Apr 3rd, 2009 at 5:20am
Harbor Freight Air Compressor 47065
I need an oil window for Air Comps 47056. Any one know where I can get one ? Helppppp. THanks
-
Posted by lyle.a.foley on Mar 30th, 2009 at 4:46pm
How to load staples
Just got this used Sears Craftsman Electric Staple Gun with no manual. Need to figure out how to load the staples. I can pull out the shaft at the bottom but cannot see how to retract the spring.
-
Posted by paulbiggc on Mar 29th, 2009 at 3:11pm
broken switch
I need a new switch for the above unit how do I order or where can I purchase one.
-
Posted by bohney on Mar 29th, 2009 at 2:02pm
manual/power adapter
The manual has no referance to the correct , Polarity Voltage or Amperees required. This is my problem with 95914 Any accurate information will be appriciated
-
Posted by fmoonliter on Mar 28th, 2009 at 8:06am
won't fire
my nail gun won't fire nails.the nail ram wouldn't return either. any suggestions. fmoonliter@gmail.com
-
Posted by pitgreenman on Mar 27th, 2009 at 10:37pm
help
can i hook this up to my pc so i can record and watch my business at home?
-
Posted by pitgreenman on Mar 27th, 2009 at 2:22pm
want to record from home not from business
want to record from home not from my business how do i do that?
-
Posted by rowley on Mar 27th, 2009 at 1:34pm
21 GAL VERTICAL OIL LUBED AIR COMP
THE LITTLE BLACK BOX THAT HAS THE ON OFF SWITCH ON HAS A RUBBER DISK ON THE BOTTON OF IT. IT IT WORN OUT WHERE CAN I GET ANOTHER?????
-
Posted by southernthumper on Mar 27th, 2009 at 12:28pm
nails
cross reference all nail types for this nailer
-
Posted by richs13 on Mar 22nd, 2009 at 7:37pm
insufficent charge
When placed on a low charged battery the charger will charge for a few minutes and then sotp and the green light come on saying the battery is charged.
-
Posted by patrickewing1960 on Mar 21st, 2009 at 5:48pm
Are staples supported also?
i purchased this air tool at harbor frieght and it came with nails and staples. Does it really support staples? If so, how are they loaded? The label on the unit only mentions brad nails 3/8'' to 1-3/16''
-
Posted by eprice1 on Mar 18th, 2009 at 7:56pm
nail won't go in deep enough
nail gun won't shoot nail in flush. after shooting nail you can still feel the top of the nail in the molding. is there a way to adjust the gun to shoot the nail in deeper.
-
Posted by dlrbubbles on Mar 18th, 2009 at 2:28pm
color security camara
how do i download the link for the manual
-
Posted by kangeo on Mar 16th, 2009 at 8:35am
oil spill out of oil retainer plug
air compressor model 40400
oil bubble out of the oil retainer and spill out on the floor. The oil seem to have air bubbles in the oil sight and the spilled oil.
-
Posted by amyd on Mar 14th, 2009 at 8:07pm
door assembly
door assembly instructions are not clear
-
Posted by ddiez on Mar 14th, 2009 at 6:35pm
Video cable length
I would like to know if I can shorten the length of the cable
-
Posted by waldosdog on Mar 13th, 2009 at 9:57am
Unknown Part
I found this item in the box when I was assembling my drill press. Having never owned one before, and shop class was soooo long ago. I was wondering what the heck it was for? I hope the picture helps. I couldn't find anything like it in the owners manual. Thanks
-
Posted by stouth17 on Mar 12th, 2009 at 4:37pm
manual
looking for compressor oil capacity
-
Posted by dwilson on Mar 11th, 2009 at 3:55pm
Central Pneumatic model 95275 compressor
Compressor stopped working. Hit the reset button to no avail. The unit doesn't seem to fill with air. Motor turns on and sounds as if it is working but it's not functioning properly.
-
Posted by nblindle on Mar 9th, 2009 at 5:49pm
How do I read Manual
I have tried to read the manual and it will not open
-
Posted by hendrickk on Mar 7th, 2009 at 2:01pm
Air Compressor Not Working
My husband passed away in December, and I do not know where he put the owners' manual for his Central Pneumatic Air Compressor 93271-1vga. The pressure gauge is showing low pressure, but the air compressor is not turning on to refill the tank. I would appreciate any help troubleshooting this.
-
Posted by bosstang on Mar 7th, 2009 at 11:41am
LOOKING TO REPAIR
This is a clipped head Framing nail I need a new set of Seals is there a kit to rebuild this gun. Has only seen light use seals are just dried out from previous owner.
-
Posted by radle on Mar 3rd, 2009 at 9:48pm
Air nailer
The plunger/nail driver will drive the nail but will not come back up on it's own. I've had it apart a number of times check everything over and I'm wondering if it has anything to do with the "O" rings. Wverything else looks OK
-
Posted by jward18 on Mar 2nd, 2009 at 7:17pm
? on floor nailer model 94446
i have a central pneumatic -2 in 1 cleat/staple floor nailer--- can i use stanley 18 gauge 2 " cleats?
on box it says 16 gauge and on your web site it says 15 gauge which is correct.
on box of that the came in it doesn't say size gauge .
is 18 gauge cleats thicker or stronger than 16 …
-
Posted by mintcondition.bachman on Feb 28th, 2009 at 11:28am
93142
19.2 V Cordless Drill....when we moved I lost the charger for this drill. Where can I get the charger?
-
Posted by chodson on Feb 26th, 2009 at 1:32pm
aircompressor
only pumping up to 80 psi bypassing oil rings are going bad. m/n38898
-
Posted by regmasako on Feb 25th, 2009 at 11:03pm
Motor specefications
What is the 12 Volt current rating on the 3000 pound WINCH when in use?
-
Posted by jfowler on Feb 24th, 2009 at 8:57am
nail gun
need to know what kind of nails for a Central pneumatic framing nailer Model #46240
Understanding Home Soldering Irons
Power Saws: An Option for Every Task
Belt Sanders Are Not Just for Professionals
