Aube Technologies TH132 A/F/AF Thermostat User Manual


 
Thank you for choosing the Aube TH132, a programma-
ble thermostat that provides both energy savings and total
comfort.
WARNING: This control module has 20-second cycles
and must be installed ONLY with a TRIAC relay.
! DAY/HOUR/MIN—Set the day and clock settings.
" PGM—Program the schedule (programs).
# MODE—Select the operating mode.
RETURN—To exit a function.
$ To configure temperature setpoints:
Comfort
, Economy and Vacation.
% Adjust the floor temperature limit (AF only).
& —Increase and decrease temperature.
' —Indicates the number of the current
program when Automatic mode is enabled.
( Current operating mode (auto manual ). In
Auto mode, the program’s associated setpoint icon is
also displayed (
).
) Indicates the room OR floor temperature.
* Heating indicators (see “Temperature Control”
below).
TH132-A
This model has been designed to control a room’s ambi-
ent temperature.
The TH132-A has one temperature sensor located in the
control module.
TH132-AF
This model is designed to use a floor sensor to control the
room temperature.
The TH132-AF has two temperature sensors:
The first one, installed in the control module, controls
the ambient temperature.
The second one, installed in the floor (and connected
to the power base), limits the temperature of the floor
(the default setting of this limit is 82°F).
TH132-F
This model is designed to control floor heating systems.
The TH132-F has one temperature sensor installed in the
floor (sensor is connected to the power base).
The TH132 has two switches, located on the upper-left
part on the rear of the control module, which are used to
set the following options:
Early Start
When the Early Start function is enabled (disabled by
default), the TH132 calculates the optimum system start
time to obtain the desired temperature by the set time. To
enable this function:
Position switch #1 down.
Note: When this function is enabled, the
system can be activated before the pro-
gram’s start time.
Temperature Display
By default, the TH132 displays the temperature in °C. If
you wish to change to °F:
Position switch #2 up.
Note: When you switch from °C to °F or vice
versa, the , and setpoints must be
redefined.
Control Module
TH1 32 A/F/AF
Owner s Guide
TH1 32 Description Models Overview Configure the Switches
Align the bracket tabs on the control module with the
holes located on top of the power base.
This control module must be installed on a PB130-024T
series power base.
Note: Keep the thermostat's air vents clean and free from
obstructions.
Note: The screw cannot be removed completely.
On the first installation, the screen displays:
0:00, MO, and temperature (room/floor).
For Floor Heating Installations:
One of the two following messages may be dis-
played when a problem occurs:
LO: The floor temperature is below 32°F (0°C), or
the temperature sensor is defective, or not
connected.
The heating indicator is displayed and
the relay is closed (energized).
HI: The floor temperature is above
140°F (60°C), or the temperature sensor is
defective.
! Set the time (HOUR - MIN).
" Set the day (DAY).
If you remove the module from its base for more than
2 hours, the time and day will have to be reprogrammed.
Comfort and Economy Setpoints
These setpoints are associated with the schedule’s pro-
grams (prog. 1 & 3 = Comfort, prog. 2 & 4 = Economy)
and are preprogrammed as follows:
A & AF models— 68°F, 64°F
F model— 82°F, 68°F
To modify a setpoint:
! Set the temperature using and press and hold the
or button until it is displayed on the screen.
" Press MODE/RETURN to exit.
Vacation Setpoint
The vacation setpoint is associated to the Vacation oper-
ating mode and is preprogrammed to 50°F. To modify this
setpoint, repeat above steps.
Floor Temperature Setpoint (AF model only)
The floor temperature limit is preprogrammed to 82°F to
avoid damage to your floor.
To modify, press the adjustment button (below ) using a
pointed object, set the desired temperature using and
press MODE/RETURN to exit.
The TH132 offers three operating modes:
Automatic Executes the schedule.
! Press MODE to select . The current
program number is displayed.
You can temporarily bypass the current
program by setting a specific temperature setpoint
or by selecting one of the pre-defined setpoint
buttons ( ). The new setpoint will be maintained
until the beginning of the next program.
Manual —Maintains a constant temperature.
! Press MODE to select .
" Set temperature or select one of the pre-
defined setpoint buttons ( ).
Vacation —Maintains the Vacation setpoint
during a prolonged absence.
Press .
Install the Control Module First Power ON
Set the Time and Day
Adjust the Temperature Setpoints Select the Operating Mode
400-132-012-A