Black & Decker Workmate 225 Type 6 Biscuit Joiner User Manual


 
FRAME
CADRE
BASTIDOR
REAR JAW
MÂCHOIRE ARRIÈRE
MORDAZA TRASERA
A.
C.
B.
FRONT JAW
MÂCHOIRE AVANT
MORDAZA FRONTAL
D.
VISE SCREW
VIS D’ÉTAU
ESPARRAGO
E.
PIVOT NUT
ÉCROU DE PIVOT
TUERCA DE GIRO
F.
VISE CRANK
MANIVELLE D’ÉTAU
MANIVELA DE LA PRENSA
G.
CRANK HANDLE
POIGNÉE DE MANIVELLE
ASA DE LA MANIVELA
H.
SWIVEL PEGS
MORDACHES ORIENTABLES
TOPES GIRATORIOS
J.
SOCKET WRENCH
CLÉ À DOUILE
DADO
K.
FRONT TOP BLOCKS
CALES SUPÉRIEURES AVANT
BLOQUES DE REMATE FRONTALES
L.
REAR TOP BLOCKS
CALES SUPÉRIEURES ARRIÈRE
BLOQUES DE REMATE TRASEROS
M.
BOLTS
BOULONS
TORNILLOS
N.
PINS
CHEVILLES
PERNOS
P.
WASHERS
RONDELLES
ARANDELAS
O.
RUBBER FEET
BOUT DE CAOUTCHOUC
REGATONES DE GOMA
FRAME
CADRE
BASTIDOR
REAR JAW
MÂCHOIRE ARRIÈRE
MORDAZA TRASERA
A.
C.
B.
FRONT JAW
MÂCHOIRE AVANT
MORDAZA FRONTAL
D.
VISE SCREW
VIS D’ÉTAU
ESPARRAGO
E.
PIVOT NUT
ÉCROU DE PIVOT
TUERCA DE GIRO
F.
VISE CRANK
MANIVELLE D’ÉTAU
MANIVELA DE LA PRENSA
H.
SWIVEL PEGS
MORDACHES ORIENTABLES
TOPES GIRATORIOS
I.
SOCKET WRENCH
CLÉ À DOUILE
DADO
J.
FRONT TOP BLOCKS
CALES SUPÉRIEURES AVANT
BLOQUES DE REMATE FRONTALES
K.
REAR TOP BLOCKS
CALES SUPÉRIEURES ARRIÈRE
BLOQUES DE REMATE TRASEROS
L.
BOLTS
BOULONS
TORNILLOS
M.
PINS
CHEVILLES
PERNOS
N.
RUBBER FEET
BOUT DE CAOUTCHOUC
REGATONES DE GOMA
G.
CRANK HANDLE
POIGNÉE DE MANIVELLE
ASA DE LA MANIVELA
O.
WASHERS
RONDELLES
ARANDELAS
Thank you for choosing Black & Decker! To register your new product go to
www.BlackandDecker.com/NewOwner
PLEASE READ BEFORE RETURNING THIS PRODUCT FOR ANY REASON.
If you have a question or experience a problem with your Black & Decker purchase,
go to http://www.blackanddecker.com/instantanswers
If you can’t find the answer or do not have access to the Internet,
call 1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. - Fri. to speak with an agent.
Please have the catalog number available when you call.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
VEA EL ESPANOL EN LA CONTRAPORTADA.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.
ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
Workmate
®
225 tYPe 6
INSTRUCTION MANUAL
Catalog Number
WM225 TYPE 6
CRANK
MANIVELLE
MANIVELA
FOOTREST (NO STEP)
REPOSE-PIED (PAS UN MARCHEPIED)
DESCANSO PARA LOS PIES (NO ESCALON)
FOLDING LEGS
PIEDS ESCAMOTABLES
PATAS PLEGABLES
SNAP-IN KNOBS
BOUTONS À ENCLENCHER
MANGOS DE LA MANIVELA
FRONT VISE JAW
CHOIRE AVANT
MORDAZA FRONTAL
REAR JAW
CHOIRE ARRIÈRE
MORDAZA TRASERA
RELEASE LEVER
LEVIER DE CLENCHEMENT
PALANCA DE LIBERACIÓN
I
MPORTANT SAFETY INSTRUCTIONS
1. Do not load with more than 450 pounds.
2. Do not apply an unbalanced load which could cause the work center to tip over.
3. Do not use the work center as a stepladder or standing platform. Do not use the lower
platform as a step when the work center is in “Workbench” position. The footboard is a
foot REST only.
4. Do not store work center outdoors or in a damp location.
5. Avoid applying excessive force when clamping with the swivel pegs.
6. Be sure that the legs are fully open (for workbench height) and be sure that the table
locks in position.
7. When using a power tool with the work center, follow the safety instructions in the
tool’s instruction manual.
8. Always wear safety glasses when operating power tools.
9. An even pressure of the vise jaws on the workpiece is essential. Tighten both crank
handles uniformly.
SAVE THIS MANUAL FOR FUTURE REFERENCE
IMPORTANT SAFETY WARNINGS AND INSTRUCTIONS
TO REDUCE RISK OF INJURY:
• Beforeanyuse,besureeveryoneusingthistoolreadsandunderstandsallsafety
instructions and other information contained in this manual.
• Savetheseinstructionsandreviewfrequentlypriortouseandininstructingothers.
READ ALL INSTRUCTIONS
ASSEMBLY:
The Workmate
®
225 Type 6 work center comes partially assembled. A standard hammer
isrequiredforassembly.Aplasticsocketwrenchisincluded.Emptythecontentsofthe
box and identify all components (see Figure 1). Place the frame (A) on the floor in the
position shown in Figure 1. Find the release levers near the front rubber feet on the sides
of the frame. Depress both release levers as shown in Figure 2 and pull up until you hear
the frame lock in place.
VISE JAW BRACKET:
1. Selectthevisescrews(D) and the pivot nuts (E).Screwonepivotnutontoeachvise
screw about halfway as shown in Figure 3, assemble washer (O) on vise screw.
2. Insert the unthreaded end of the vise screws into the frame such that the pivot nuts
are located in the slots on the top of the frame and the unthreaded ends protrude
through the holes in the front of the frame, as shown in Figures 3 and 4.
3. Install the two vise cranks (F) and secure them by driving the pins (M) through the
holes in the cranks and the vise screws. (Align the holes in the vise cranks with the
holes in the vise screws and strike the pins sharply with a steel hammer until they
areflushwiththesidesofthevisecranks.)SeeFigure 5.
4. Closely examine the two front top blocks and the two rear ones. Note that the front
blocks do not have a protruding tab on the bottom side where the rear blocks do.
Selectthefrontvisejaw,(B), and the two front top blocks, (J). Place the top blocks
on the rails of the frame as shown in Figure 6.
5. Install the front vise jaw on top of the top blocks so that the small holes at each end
of the jaw fit down over the posts on the top side of the blocks. With the jaw
positioned as described above insert into the frame as shown in Figure 6, insert two
of the four bolts, (L) into the holes in the jaw and tighten them securely into the holes
in the pivot nut. Use the socket wrench, (I) provided, shown in Figure 1.
NOTE: For clarity, only the left side assembly is shown. Perform all operations
on right side as well.
6. Selecttherearvisejaw,(C) and the two rear top blocks, (K). Position the rear top blocks
on the frame rails so that the tab ears in the bottom of the blocks fit into the key holes
of the frame rail. Position the top blocks so their raised posts are toward the rear of the
frame, as shown in Figure 7. Now install the rear vise jaw so that the small holes in the
ends of the jaw fit over the raised posts on the top blocks you just installed.
7. Insert the remaining two bolts,
(L)
into the holes in the jaw and through the top
blocks into the raised posts of the vise guides. The holes in the rear blocks are not
threaded so you will feel resistance as you cut threads into them.
8.Snap-incrankhandleasshownin Figure 8.
9. ToassembletherubberfeettoyourWorkmate:Turntheunitupsidedown.Swing
out the four legs to the fully extended and locked position. Align the rubber foot with
the leg as shown in Figure 9. Lightly tap foot into place with a hammer.
CHANGING THE INDEXED POSITION OF THE REAR JAW:
1. Install the rear jaw in 1 of 3 possible indexed “keyhole” positions by indexing the rear
visejawintoakeyholeinthevisejawbracket.Securetherearjawbyslidingittothe
back of the keyhole. As shown in Figure 7.
SWIVEL PEGS:
1. The four supplied swivel pegs can be used in any of the holes in the front and rear
jaws. The pegs are used to extend the dimensions of your Workmate’s holding
capacity. (Figure 10)
SERVICE INFORMATION
Black&Deckeroffersafullnetworkofcompany-ownedandAuthorizedService
locationsthroughoutNorthAmerica.AllBlack&DeckerServiceCentersarestaffedwith
trained personnel to provide customers with efficient and reliable power tool
service. Whether you need technical advice, repair, or genuine factory replacement
parts, contact the Black & Decker service location nearest you. To find your local
servicelocation,refertotheyellowpagedirectoryunder“Tools—Electric”orcall:
1-800-54-HOW-TO.
LIMITED TWO-YEAR HOME USE WARRANTY
Black&Decker(U.S.)Inc.warrantsthisproductfortwoyearsagainstanydefects
in material or workmanship. The defective product will be replaced or repaired at no
charge in either of two ways: The first, which will result in exchanges only, is to return
the product to the retailer from whom it was purchased (provided that the store is a
participating retailer). Returns should be made within the time period of the retailer’s
policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be
required.Pleasecheckwiththeretailerfortheirspecificreturnpolicyregardingreturns
that are beyond the time set for exchanges. The second option is to take or send the
product(prepaid)toaBlack&DeckerownedorAuthorizedServiceCenterforrepairor
replacementatouroption.Proofofpurchasemayberequired.Black&Deckerowned
andAuthorizedServiceCentersarelistedunder“Tools-Electric”intheyellowpagesof
the phone directory. This warranty does not apply to accessories. This warranty gives
you specific legal rights and you may have other rights which vary from state to state.
Shouldyouhaveanyquestions,contactthemanagerofyournearestBlack&Decker
ServiceCenter.This product is not intended for commercial use.
FIG. 2
FIG. 1
PDF created with FinePrint pdfFactory trial version www.pdffactory.com
FIG. 3
RELEASE LEVER
LEVIER DE DÉCLENCHEMENT
PALANCA DE LIBERACIÓN
FIG. 4
FIG. 6
FIG. 5
FIG. 7 FIG. 8
FIG. 9 FIG. 10
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286
U.S.A.
See ‘Tools-
Electric’
– Yellow Pages –
for Service &
Sales
AVANT DE RETOURNER LE PRODUIT, PEU IMPORTE LA RAISON, PRÉRE DE
COMPROSER LE 1 800 544 6986
Modèle WM225
GUIDE D’UTILISATION
IMPORTANTES MESURES DE SÉCURITÉ
1. Nejamaisplacerunechargesupérieureà204kg(450lb)surl’étau-établi.
2.
Nejamaisplacersurl’étau-établiunechargemaléquilibréequipourraitlefairebasculer.
3. Nejamaisseservirdel’étau-établicommemarchepiednicommeplate-forme.Ne
pasmontersurlaplate-formeinférieurelorsquel’étau-établiestenpositiond’établi.
Lerepose-piedsertseulementàseREPOSER les pieds.
4. Nepasrangerl’étau-établiàl’extérieurnidansunendroithumide.
5. Éviter de trop serrer les mâchoires des mordaches orientables.
6. S’assurerquelespiedssontpleinementécartésetqueleplateauestverrouilléen
position de chevalet.
7. Respecter les consignes de sécurité contenues dans les guides d’utilisation des
outilsélectriquesutilisésavecl’étau-établi.
8. Toujoursporterdeslunettesdesécuritélorsqu’onutilisedesoutilsélectriques.