Filter
Top Products
SKU 93009
For technical questions, please call 1-800-444-3353
Page 10
Maintenance
1. Take care in maintaining this tool. It will serve you well and for a long time if properly stored, cleaned
and maintained.
2. Keep the tool clean, by cleaning it after each job, before storing it. During large jobs, check and clean
the tool after each hour or two of use.
3. Periodically check the condition of the power cord to assure that it has not been damaged. If the cord
is damaged, have it repaired or replaced by a qualified service technician.
4. Periodically check the condition of the blades. Be sure they remain sharp and are properly and tightly
installed. If a blade or spacer becomes loose, turn off the tool, unplug it from its power source, and
tighten the blade before continuing. If the blades do not cut properly, turn off and unplug the tool.
Check to be sure they are sharp and in good condition. If not, replace the blades before continuing.
5. Always turn off the tool and unplug it from its power source whenever the tool is not in use, whenever
you service or adjust the machine, and whenever you are changing blades or accessories.
6. If any damage is noted to this tool, repair it before continuing use. Have all repairs done by a qualified
service technician.
Troubleshooting
melborPesuaCelbissoPnoituloS
ffosnrutdnatohsemocebrotomehT
yldetcepxenu
.detavitcasahhctiwstuotucytefaslam
rehtehT
roftiawdna,lootehtgulpnu,FFOhctiwSehtnruT
gnitratseryrt,loocsitiretfA.nwodloocotlooteht
.looteht
.tewrodegamadsirotuodenrubsahrotomehT
aybderiaperrodetcepsnirotomehtevaH
.naicinhcetecivresdeifilauq
.no
nruttonlliwdnaFFOsilootehT .detavitcasahhctiwstuotucytefaslamrehtehT
roftiawdna,lootehtgulpnu,FFOhctiwS
ehtnruT
gnitratseryrt,loocsitiretfA.nwodloocotlooteht
.looteht
.degamadsihctiwSehT
deifilauqaybderiaperro
detcepsnilootehtevaH
.naicinhcetecivres
.FFOsiylppusrewopruoynirekaerbtiucricehT
lootsihtevoM.rekaerbtiu
cricehtteserdnakcehC
emosevomerro,yticapacretaerghtiwtiucricaot
.tiucricehtmorfsecnailpparehto
.ralugerr
isilennahcehtdna,tluciffidsignittuC .tnebroesool,lluderasedalbehT
ehtfonoitidnocehtkcehcdnalootehtgulpn
U
.yrassecenfiecalpeR.sedalb
.ylivaehsetarbivlootehtgnittucgniruD .lludrodemrofed,detaehrevoerasedalbehT
ehtfonoitidnocehtkcehcdnalootehtgulpnU
.yrassecenfiecalpeR.sedalb
.ysionyrevsiroyllacitarresnurlootehT .
dekcarcronrowerasehsurbnobracehT
deifilauqaybderiaperrodetcepsnilootehtevaH
.naicinhcetecivres
6. After work is completed, release the Power Switch (30) to turn OFF the machine. Unplug the power
cord from the power source.
7. Allow the tool to cool down before cleaning it.
8. After the machine has cooled down, and is unplugged, clean it with a dry brush to remove cement dust
and other debris.
9. Disconnect any Dust Extraction System you may be using.
10. Wind up the tool’s power cord, and put the tool away for safekeeping. Always store it in a dry area out
of reach of children and unauthorized persons.