Open as PDF
1. The LED indicator will automatically switch off after 5 seconds from
pressing the button.
2. When the battery pack connects to the USB power, the LED indicator will
light indicating the charging status. Press the button for switching off the
indicator, and simply press again to switch on the LED indicator.
• USB Battery Pack (CPBC10400 Series)
• User Guide
Battery Capacity: 10400mAh
Rated Input: DC 5V, 2A
USB Output: 5V, 2.1A
Micro USB Output: 5V, 1A
Charging time: ~7 Hours by the 2A power
Dimension: 4.42x3.06x1.05 inch
Weight: 9.14 oz
Storage: 14 to 122˚F (-10 to 50˚C)
Operation: 32 to 104˚F (0 to 40˚C)
IMPORTANT! PRIOR TO FIRST USE
The CPBC10400 Series is packaged in a protection mode
for shipping. Prior to use, connect the CPBC10400 Series
to a USB power source to set it to normal mode and the
suggested a full 10-hour charge.
TO CHARGE THE BATTERY PACK
Charge the USB Battery Pack by attaching the USB charging
connector to any powered USB port, including but not limited
to the USB wall charger, desktop computer, laptop or USB
powered hub. When charge the battery pack, the LED
indicator would light up automatically. Press the button to turn
off if it is not required.
Recharge the CPBC10400 Series every 3 months when not
use to ensure the best battery performance. The battery
capacity may decline after 300 times usage.
Before using the USB Battery Pack, please read the following
warnings carefully. Use the product according to the
procedures described in this manual. Failure to follow these
safety precautions may result in fire, explosion, electrical
shock or other dangers.
1. Do not disassemble this product, or any of its parts.
2. Store between 14 to 122°F (-10 to 50°C).Operate between
32 to 104°F(0 to 40°C).
3. Do not immerse this product in water or other liquids, as
such use may result in fire or electrical shock. If water or
other liquids enter the battery interior, unplug the product
immediately from any attached power source or device.
4. Do not use this product with wet hands. Moisture in or on
this product may result in electrical shock.
5. Do not expose this product to direct flame or leave it in an
overheated condition, as the battery may explode.
6. Store this product in a cool and dry environment when not in use.
7. Do not puncture this product. Puncturing the battery may
cause the release of harmful substances.
8. It is normal for the USB Battery Pack to become warm
9. Keep this product out of the reach of children. Ensure that
all users read these warnings and instructions before using.
10. Please recycle USB Battery Pack in accordance with local
environmental laws and regulations
FCC Part 15
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates uses and can radiate
The USB Battery Pack (CPBC10400 Series) is a
rechargeable lithium-ion battery with the high capacity that
is designed for powering up to two mobile devices such as
phones, MP3 players, tablets, and handheld gaming
devices while away from other power sources.
- Compact and portable design
- Dual output
- Built in USB input power cable
- Built in micro USB output connector
- Battery life indicator
CyberPower Systems, Inc.
© 2013 CyberPower Systems, Inc.
All rights reserved. Reproduction in whole or in part without permission is prohibited.
USB BATTERY PACK
Model: CPBC10400 Series
USB Input Cable
Micro USB Output Connector
USB Output Port
Power On/ LED Indicator Switch
Flash Light On/ Off
LED Battery Life lndicator
5V/ 2A USB input
5V/ 1A Micro USB output
5V/ 2.1A USB output
Press the button
Press and hold 3 seconds
As the “LED INDICATOR”
CONDITIONNO. LED INDICATION
Battery Life Indicator
Four LEDs represent 25%,
50%, 75% and 100% battery
life from left to right side.
All four LEDs are flash simultaneously.
The first LED is flashes rapidly.
C.The battery pack is
charging the device
and the power source
is charging the
The device can’t be charged
when the power source is
charging the battery pack.
The solution is to remove the
device from the battery pack.
between charger and
USB Battery Pack.
b.No power from the
C.Short Circuit of
battery pack product
Re-attach the USB connector
to the USB port.
a.Check that power is provided
to the USB port.
b. The battery pack has a low
charge. Recharge the
power battery pack.
Reset the battery pack.
Problem Possible Cause Solution
a.The power of device
is over specification.
b.The battery is out
Check the power specification
of the device before charging
with the CPBC10400 Series
Charge the battery pack via a
radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
If the LED indicator extinguishes automatically during the
charging process, press the button to revert.
Changes or modifications not expressly approved by the
party responsible for compliance with the FCC Rules could
void the user’s authority to operate this equipment.
LIMITED PRODUCT WARRANTY
CyberPower offers limited product warranty for the hardware of
the USB Battery Pack* and the product is free from material
and manufacturing defects for one year. (*battery excluded) A
reasonable purchase proof with date must be provided when
submission. CyberPower's sole responsibility is to repair or
replace the product if a material or manufacturing defect results
in product failure during its normal use. The warranty is void if
the product is damaged due to abuse, alteration, misuse,
negligence, incorrect voltage supply, air/water pollution,
accidents and natural disasters.