Filter
Top Products
12450ML-99 Rev.F MQS1297/0202
Set Default Decimal Point
1. Press MENU. The meter displays:
2. Press ᮣ/MIN to display the current
decimal point. Change the display, if
necessary, to read “FFFFFF.” (Use
ᮡ/MAX to change the decimal point
position).
3. Press MENU. The meter stores changes (if applicable),
then displays “CNT BY”.
4. Press RESET twice. The meter momentarily displays
“RESET 2” then returns to the run mode. The meter
will now read the input signal (4mA = ≈ 000000.
and 20mA = ≈ 020000.).
Measure and Record Input Values
1. Apply 4mA to the input and record the
display reading.
INPUT 1 = _________________
Refer to this as Input One.
2. Apply 20mA to the input and record the
display reading.
INPUT 2 = _________________
Refer to this as Input Two.
3. Press MENU until the meter displays:
4. Press MENU until the meter displays:
Press ᮣ/MIN to display “INP6=0”
Change the meter to read “INP.6=1”
(Use ᮣ/MIN to scroll through digits
and ᮡ/MAX to change the digit’s value).
5. Press MENU. The meter stores changes and displays:
DP41-E
High Performance Process Indicator
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and
workmanship for a period of 13 months from date of purchase. OMEGA Warranty adds an
additional one (1) month grace period to the normal one (1) year product warranty to cover
handling and shipping time. This ensures that OMEGA’s customers receive maximum
coverage on each product.
If the unit should malfunction, it must be returned to the factory for evaluation. OMEGA’s
Customer Service Department will issue an Authorized Return (AR) number immediately upon
phone or written request. Upon examination by OMEGA, if the unit is found to be defective it will
be repaired or replaced at no charge. OMEGA'S WARRANTYdoes not apply to defects resulting
from any action of the purchaser, including but not limited to mishandling, improper interfacing,
operation outside of design limits, improper repair, or unauthorized modification. This
WARRANTYis VOID if the unit shows evidence of having been tampered with or shows evidence
of being damaged as a result of excessive corrosion; or current, heat, moisture or vibration;
improper specification; misapplication; misuse or other operating conditions outside of OMEGA’s
control. Components which wear are not warranted, including but not limited to contact points,
fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA
neither assumes responsibility for any omissions or errors nor assumes liability for any damages
that result from the use if its products in accordance with information provided by OMEGA, either
verbal or written. OMEGA warrants only that the parts manufactured by it will be as specified and
free of defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY
KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED
WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE HEREBYDISCLAIMED. LIMITATION OF LIABILITY: The remedies
of purchaser set forth herein are exclusive and the total liability of OMEGA with respect to this
order, whether based on contract, warranty, negligence, indemnification, strict liability or
otherwise, shall not exceed the purchase price of the component upon which liability is based. In
no event shall OMEGA be liable for consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a
“Basic Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2)
in medical applications or used on humans. Should any Product(s) be used in or with any nuclear
installation or activity, medical application, used on humans, or misused in any way, OMEGA
assumes no responsibility as set forth in our basic WARRANTY / DISCLAIMER language, and
additionally, purchaser will indemnify OMEGA and hold OMEGA harmless from any liability or
damage whatsoever arising out of the use of the Product(s) in such a manner.
RETURN REQUESTS / INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department.
BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN
AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER SERVICE
DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number
should then be marked on the outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to
prevent breakage in transit.
FOR W
ARRANTY RETURNS, please have
the following information available BEFORE
contacting OMEGA:
1. P.O. number under which the product
was PURCHASED,
2. Model and serial number of the product
under warranty, and
3. Repair instructions and/or specific
problems relative to the product.
FOR NON-W
ARRANTY REPAIRS, consult
OMEGAfor current repair charges. Have the
following information available BEFORE
contacting OMEGA:
1. P.O. number to cover the COST of the
repair,
2. Model and serial number of product, and
3. Repair instructions and/or specific
problems relative to the product.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is
possible. This affords our customers the latest in technology and engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2002 OMEGA ENGINEERING, INC. All rights reserved.
This document may not be copied, photocopied, reproduced, translated, or reduced to any
electronic medium or machine-readable form, in whole or in part, without prior written consent
of OMEGA ENGINEERING, INC.
PATENT NOTICE: This product is covered by one or more of the following patents: U.S.
Pat. No. Des. 336,895; 5,274,577 / CANADA 2052599; 2052600 / ITALY 1249456;
1250938 / FRANCE BREVET No. 91 12756 / SPAIN 2039150; 2048066 / UK PATENT
No. GB2 249 837; GB2 248 954 / GERMANY DE 41 34398 C2. The “Meter Case Bezel
Design” is a trademark of NEWPORT Electronics, Inc., registered in the U.S. USED
UNDER LICENSE. OTHER INTERNATIONAL PATENTS PENDING.
Scale Input Values
1. Press ᮣ/MIN to display “INPUT 1”:
Press ᮣ/MIN again. The meter
displays “000000”. Enter the INPUT 1
value recorded in step 1 of the Measure
Input Values section of this quick start.
2. Press MENU. The meter displays
“READ 1”:
Press ᮣ/MIN to display a six-digit
number. Change the meter to read
“000000”. (Use ᮣ/MIN to scroll
through digits and ᮡ/MAX to change
the digit’s value.)
3. Press MENU. The meter displays
“INPUT 2”:
Press ᮣ/MIN. The meter displays
“000000”. Enter the INPUT 2 value
recorded in step 2 of the Measure Input
Values section of this quick start.
4. Press MENU. The meter displays
“READ 2”:
Press ᮣ/MIN to display a six digit
number. Change the meter to read
“001000”. (Use ᮣ/MIN to scroll through
digits and ᮡ/MAX to change the digit’s value.)
5. Press MENU. The meter stores changes and displays:
6.
Press ᮣ/MIN to display the current decimal point. Press
ᮡ/MAX to change the decimal point location to “FFFFF.F”.
7.
Press MENU. The meter stores this change, then displays
“CNT BY”
8. Press RESET twice. The meter displays:
“RESET 2”, then returns to the run
mode. The meter is now scaled to
read 0 to 100.0 for a 4-20 mA input.
5 6
stored
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
CNTBY
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
INPUT1
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
INPUT2
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
stored
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
IN.SC.OF
ᮡ
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
IN CNF
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
INp6=0
ᮡ
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
INPUT2
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
INPUT1
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
READ 1
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
READ 2
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
stored
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
CNTBY
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
stored
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
Dec pt
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
REset2
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
Dec pt
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
FFFFFF.
SETPTS
/MAX
ᮣᮡ
/MIN
MENU
RESET
TRADEMARK NOTICE:
®
,
omega.com
®
,
are trademarks of OMEGA
Engineering, Inc.
®
This device is marked with the international caution symbol. It is important to read the
SetupGuide before installing or commissioning this device as it contains important
information relating to safety and EMC.
WARNING: These products are not designed for use in, and should not be used for, patient
connected applications.
It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply.
OMEGA is constantly pursuing certification of its products to the European New Approach
Directives. OMEGA will add the CE mark to every appropriate device upon certification.
The information contained in this document is believed to be correct, but OMEGA Engineering,
Inc. accepts no liability for any errors it contains, and reserves the right to alter specifications
without notice.
Servicing North America:
USA: One Omega Drive, P.O. Box 4047
ISO 9001 Certified Stamford CT 06907-0047
TEL: (203) 359-1660 FAX: (203) 359-7700
e-mail: info@omega.com
Canada: 976 Bergar
Laval (Quebec) H7L 5A1
TEL: (514) 856-6928 FAX: (514) 856-6886
e-mail: info@omega.ca
For immediate technical or application assistance:
USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA
®
Customer Service: 1-800-622-2378 / 1-800-622-BEST
®
Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN
®
TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA
Mexico and TEL: (001)800-TC-OMEGA
®
FAX: (001) 203-359-7807
Latin American: En Espa
ñol: (001) 203-359-7803
e-mail: info@omega.com.mx
Servicing Europe:
Benelux: Postbus 8034, 1180 LA Amstelveen, The Netherlands
TEL: +31 20 3472121 FAX: +31 20 6434643
Toll Free in Benelux: 0800 0993344
e-mail: nl@omega.com
Czech Republic: Rudé armády 1868, 733 01 Karviná 8
TEL: +420 69 6311899 FAX: +420 69 6311114
e-mail: czech@omega.com
France: 9, rue Denis Papin, 78190 Trappes
TEL: +33 130 621 400 FAX: +33 130 699 120
Toll Free in France: 0800406342
e-mail: france@omega.com
Germany/Austria: Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
TEL: +49 7056 9398-0 FAX: +49 7056 9398-29
Toll Free in Germany: 0800 639 7678
e-mail: germany@omega.com
United Kingdom: One Omega Drive
ISO 9002 Certified River Bend Technology Centre
Northbank, Irlam Manchester M44 5BD United Kingdom
TEL: +44 161 777 6611 FAX: +44 161 777 6622
Toll Free in England: 0800 488 488
e-mail: sales@omega.co.uk
OMEGAnet
®
On-Line Service
www.omega.com
Internet e-mail
info@omega.com
®
®