Philips LP-11 Work Light User Manual


  Open as PDF
of 2
 
Job Information Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
"JSQPSU3PBE'BMM3JWFS."tt'BY
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt
Lighting Systems LP-11
1BHFPG -JOFBS1FSG-ZUFÜDN4FNJ1FSGPSBUFE-JHIU51FS'PPU/PNJOBM4FDUJPO
#
Bottom View
98” (248.92cm)
2” (5.08cm) 2” (5.08cm)2” (5.08cm)
13” (33.02cm)
3”
(7.62cm)
5”
(12.70cm)
Perf
Complete ordering instructions below.
Features
1. Housing:
others.
2. Lamping: Two T8 32 watt fluorescent lamps per 4-foot section. Provided by
3. Reflector: Precision die-formed specular aluminum
Module Ordering Information
Style Series Options
2T8 = 2F32T8 4 = 4-Foot U = Universal Voltage Blank = No Options
8 = 8-Foot E = Emergency Pack DS = A-B Switch
D1 = Dimming 120v X4 = 4 Wire for Dimming &
Switched Emergency
D2 = Dimming 277v
LP 2 2T8B
LengthLampsType Ballast
Electrical
Ballast is universal voltage, <10% THD, .88 ballast factor, instant start. 3 con-
ductor, 18 gauge wire. Color-coded quick connectors allow ease of connection
for joiner modules. For special circuiting consult factory. Cord is 18/3 SJT. Factory
installed ballast disconnect allows the ballast to be disconnected from and
reconnected to incoming power under load without turning the entire circuit off.
Dimming: 120/277 VAC, 4 wire feed required.
Emergency Battery Pack: 32 watt: 450 lumens @ 90 minutes.
Options
Dual Switching: Order the DS option for separate row switching. DS option
automatically ships with the X4 option included.
Mountings
Cable Suspension (not shown) - 4-1/2” (11.43cm) diameter flat canopy finished
white enamel, 1/16” (0.16cm) diameter stainless steel aircraft cable adjustable up
to 36” (91.44cm) without cutting. Overlap connector to provide 46” (116.84cm) of
perforated and 2” (5.08cm) solid sections contiguously without the presence of
hairline connections. (See Bottom View drawing above)
Ordering Information
Individual Fixtures:
1. Order number of MODULES required.
2. Order one POWER FEED END SET per MODULE.
Continuous Rows:
1. Determine run length.
2. Order the appropriate number of MODULES for the complete run.
3. Order one POWER FEED END SET per run.
4. Order one CABLE ASSEMBLY per MODULE minus one per run.
5. For runs that exceed amperage limits, order the appropriate number of SINGLE
Labels
UL, cUL and I.B.E.W.
Finish
Powder coated baked white enamel. Custom colors available, consult factory.
CABLE & CORD FEEDS.
4. Diffuser: Opal acrylic diffuser.
4 Wire: Order X4 modules for remainder of the run when using dimming and/or
switched emergency battery pack modules. Also, order the 4 Wire Cord Power Feed
End Sets (LP2EC36X4) when using 4 Wire Modules.
Emergency Circuiting: Special circuiting - consult factory.
18 gauge perforated steel with 51% open hole pattern. Holes are
1/8” (0.32cm) diameter on 5/32” (0.40cm) centers. Die-formed steel end cap
with concealed access holes for through wiring. No exposed fasteners or
hardware.