Filter
Top Products
Page 41
The model number will be found on the data plate attached to the right side panel of the cabinet, next to the
saw's on board receptacle. Always mention the model number in all correspondence regarding your TABLE
SAW or when ordering repair parts.
1 Motor Assembly.......................................... 1
2 Off/On Switch Assembly............................. 1
3 Shim ........................................................... 2
4 Hex Nut (5/8-18) ......................................... 1
5 Saw Table...................................................1
6 Front Cabinet Panel ................................... 1
7 Rear Cabinet Panel .................................... 1
8 Right Cabinet Panel ................................... 1
9 Left Cabinet Panel...................................... 1
10 Locker Bracket ........................................... 1
11 Clamper Bracket......................................... 1
12 Dust Cover..................................................1
13 Miter Table Assembly................................. 1
14 Clamp Plate ................................................2
15 Needle Roller (1/4 in. x 3/4 in.)................... 2
16 Clamp ......................................................... 1
17 Shim ........................................................... 5
18 Hex Nut (5/16-18)....................................... 2
19 Front Rail ....................................................1
20 Rear Rail..................................................... 1
21 Rail Holder Nut (5/16)................................. 4
22 Rail Locking Clamp .................................... 4
23 Bevel Gear..................................................2
24 Shaft ........................................................... 1
25 Gear Shaft .................................................. 1
26 Handle Shaft............................................... 1
27 Gear Rack .................................................. 1
28 Tilting Gear ................................................. 1
29 Clutch ......................................................... 1
30 Cam ............................................................ 1
31 Screw (8-32 x 1-3/16 in. Fil. Hd.) ............... 1
32 Hex Nut (3/4-16) ......................................... 1
33 Washer ....................................................... 1
34 Bevel Locking Lever ...................................1
35 Blade Adjusting Handle ..............................1
38 Handwheel Inner Grip ................................ 1
39 Spring ......................................................... 1
40 Spring ......................................................... 1
41 Washer ....................................................... 1
42 Washer ....................................................... 3
43 Washer ....................................................... 4
44 Hex Bolt (5/16-18 x 1-1/8 in.) ..................... 2
45 Hex Bolt (5/16-18 x 3/4 in.) ........................ 4
Key
No. Description Quan.
46 Screw (10-24 x 5/8 in. Pan Hd.) ................. 8
47 Screw (10-24 x 5/8 in. Pan Hd.) ................. 3
48 Screw (8-32 x 3/8 in. Pan Hd.) .................16
49 Nylon Hex Nut (3/8-16)............................... 1
50 Set Screw (1/4-20 x 3/8 in.)........................ 1
51 Roll Pin ....................................................... 1
52 Roll Pin ....................................................... 2
53 Name Plate................................................. 1
54 Scale Label................................................. 1
55 Outlet (15 Amp Single Pole)....................... 1
56 Cord ............................................................ 1
57 Cable Clamp............................................... 1
58 Bevel Indicator............................................ 1
59 Wire Nut......................................................1
60 Lock Nut (8-32 Hex) ................................... 3
61 Cone Disc Spring ....................................... 1
62 Retaining Ring.............................................1
63 Data Plate................................................... 1
64 Bolt (1/4-20 x 1 in. Hex) ............................. 2
65 Bolt (1/4-20 x 2 in. Hex) ............................. 1
66 Hex Nut (1/4-20) ......................................... 4
67 Screw (10-24 x 5/16 in. Pan Hd.) ............... 2
68 Plug Socket Box (A) ................................... 1
69 Plug Socket Box (B) ................................... 1
70 Screw (8-16 x 3/4 in. Pan Hd.) ................... 4
71 Locker Support ........................................... 2
73 Set Screw (10-24 x 3/8 in.)........................ 4
74 Blade Adjustment Handle Grip................... 1
75 Screw (10-24 x 1/2 in. Pan Hd.) ...............15
76 Throat Plate ................................................1
78 Cap Screw .................................................. 2
79 Label ........................................................... 1
80 Guide Holder .............................................. 1
81 V Belt .......................................................... 2
82 1/4 in. Spacer ............................................. 1
83 1/2 in. Spacer ............................................. 1
84 Blade Washer ............................................. 2
85 Screw (8-32 x 3/4 in. Pan Hd.) ................... 3
86 Shim ........................................................... 2
87 Label ........................................................... 1
89 Screw (10-24 x 1 in. Pan Hd. ..................... 4
90 End Plug F1 (front left) ............................... 1
91 End Plug F2 (front right) ............................. 1
SEE BACK PAGE FOR ORDERING INSTRUCTIONS.
Key
No. Description Quan.
RYOBI 10 in. (254 mm) TABLE SAW - MODEL NO. BT3000
PARTS LIST-FIGURE 59