Filter
Top Products
unpacking and pre-assembly
4 S
6
t t t t
15 16 17 18
Figure 1
UNPACKING AND CHECKING CONTENTS
This Craftsman Motorized Floor Saw is shipped complete
in one carton. In order to prevent damage during shipment
and facilitate packaging, certain items are removed at the
factory and must be assembled when receiyed by the pur-
chaser. These "loose" parts are listed below and should be
accounted for before discarding any packing material.
KeyNo.
IFig.1) ItemName Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Leg Base ..................................... 4
Stiffener, Leg ................................. 4
Fence, Auxiliary ............................... 1
Extension Assembly, Table Sliding ................ 1
Support, Table Extension ........................ 1
Extension, Table .............................. 2
GuardAssembly, Saw ........................... I
Gauge Assembly, Miter ......................... 1
FenceAssembly, Rip ........................... 1
Wrench, Arbor ................................. 1
Wrench, Shaft ................................. 1
Bar Assembly, Fence ........................... 1
Rack, Table .................................. 2
RodAssembly, Extension ........................ 2
Package Assembly,Loose Parts (Saw).............. 1
Package Assembly,Loose Parts (Auxiliary Fence) ..... 1
Package Assembly, Loose Parts (Leg) .............. 1
Package Assembly, Loose Parts (Extension)......... 1
Owners Manual ................................ 1
List ofLooseParts,BasicSaw(Package15, figure 1)
Spacer, Fence Guide Bar ...................... 7
Screw, Mach.,Rd.-Hd.Slotted, 1/4-20 x 2" ........ 7
Nut, Hex., 1/4-20 ............................ 7
Washer, Lock,1/4 ............................ 7
Wrench,Hex., 1/16" .......................... 1
Wrench,Hex., 3/32" .......................... 1
ii
Key No.
(Fig. 1) Item Name Qty.
II
Wrench, Hex., 1/8 ........................... 1
Wrench, Hex., 5/32" .......................... 1
Wrench, Hex., 3/16" .......................... 1
Key, Switch .................................. 2
Listof LooseParts,AuxiliaryFence(Package16, figure 1)
Clamp,Table Extension........................ 2
Screw, Mach., Hex.-Hd.,5/16-18 x 3/4" .......... 4
Nut, Hex., 5/16-18 ............................ 2
Washer, Lock,5/16 ........................... 4
Nut, Wing, 5/16-18 ........................... 4
List of LooseParts,LegAssembly(Package17, figure 1)
Screw,Mach., Hex.-Hd.,5/16-18 x 5/8" ........... 16
Nut, Hex., 5/16-18 ............................ !6
Screw, Mach., Hex..Hd., 1/4-20xl/2" ........... 15
Nut, Hex., 1/4-20 ............................ 16
Nut, Hex., 1/2-13 ............................ 8
Foot, Leveling ................................ 4
List of LooseParts,Extension(Package18, figure 1)
Screw, Mach., Hex.-Hd.,5/16-18 x 1-1/4" ......... 8
Nut, Hex., 5/16-18 ............................ 8
Washer, Lock,5/16" .......................... 8
Support,ExtensionRod ........................ 2
POWER SUPPLY AND MOTOR DATA
MOTOR SPECIFICATIONS
The AC motor used in this saw is a single voltage capacitor
start capacitor run, non-reversible type, with the following
specifications:
Voltage .......................... 240
Amperes .................... ....... 7.0