Filter
Top Products
Form
#
Z551
Date 4-99IA
C?
0
b
Model
5203
318"
Reversible
Micro
Drill
II
-----
IMPORTANT
I
I
Read
these instructions carefully before installing, operating, servicing or repairing this
tool.
Keep
these instructions in a safe accessible place,
SAFETY
MESSAGES
Personal
Safety
Equipment
Use
-
Safety
Glasses YES
Safety
rules
when using
a
5203
Drill
Use
-
Safety
Gloves
Use
-
Safety
Boots
Use
-
Breathing
Masks
Use
-
Ear
Protectors
YES
-
Use may produce flying objects. Always use safety
A
WARNING
Always Read Instructions Before
@
Using Power Tools
goggles.
-
Use accessories rated at above
1,550
RPM.
-
Prolonged exposure to vibration may cause injury.
-
Read
all
instructions before using this tool. All operators must
be fully trained in
its
use and aware of these safety rules.
-
Do not exceed the maximum working air pressure.
-
Use personal protection equipment as recommended.
-
Use compressed air only at the recommended
conditions.
-
If
the
tool aooears
to
malfunction, remove from
use
Operator Instructions
Includes:
Safetv
Rules
@
Always Wear Safety Goggles
@
Wear Hearing Protection
Avoid Prolonged Exposure
dh
T
o Vibration
immediately and arrange for service and repair. If it is not
practical to remove tool from service, then shut off the air
ores seen
Use
Work
Stations
Putting Into Service
Operating
Dismantling and
Assembly.
supply to the tool and write or have written a warning
note and attach
it
to the tool.
-
If
tool is to be used with a balancer or other suspension
device, ensure that the tool is firmly attached to the
suspension/support device.
-
When operating the tool, always keep the body and
particularly the hands away from the working attachment
fixed to the tool.
-
The tool is not electrically insulated. Never use the tool if
there is any chance of coming into contact with live
electricity.
-
Always when using the
tool,
adopt a firm footing andlor
position and grip the tool sufficiently only to overcome
any reaction forces that may result from the tool doing
work. Do not overgrip.
-
Use only correct spare parts for maintenance and repair,
Do not improvise or make temporary repairs. Major
servicing and repairs should only be
carried out bv oersons trained to do
so.
7
and easily accessible so that the air supply
to
the tool
can
be shut off in an emergency.
-
Check hose and fittings regularly for wear.
-
Take care against entanglement of the moving parts of
the tool with clothing, hair, ties, cleaning rags, rings,
jewelry, watches, bracelets, etc.This could cause the body
or parts of the body to be drawn towards and in contact
with the moving parts of the tool and could be very
dangerous.
-
It is expected that users will adopt safe working practices
and
observe all local, regional or country legal
requirements
when installing, using or maintaining the tool.
-
Take care that the exhaust air does not point towards any
other person or material or substance that could be
contaminated by oil droplets. When first lubricating a tool
or if the tool exhaust has a high oil content, do not allow
the exhaust air to come near very hot surfaces or flames.
-
Never lay the tool down until the working attachment has
stopped moving.
-
When the tool is not in use, shut off the air supply and
press throttletriggerllever to drain the supply line.
If
the
tool is not to be used for a period of
time,
first lubricate,
disconnect from air supply and store in a dry average room
temperature environment.
-
If the tool is passed from one user to a new or inexperi-
enced user, make sure these instructions are available to
be passed with the tool.
-
Do not remove any manufacturer fitted safety devices
where fitted, i.e., wheel guards, safety trigger, speed
governors, etc.
-
DO
not lock, tape, wire, etc. the 4~n/~ff1
AII
Pipe
And
Fillings
valve in 'On' position. The throttle
ShouldBe
112"
Or Larger
trigger1 lever, etc. must always be free
to return to the 'Off' position when
released.
-
Always shut off the air supply to the tool
and press the
'On/Off'
valve to exhaust
the air from the feed hose before
fitting, removing or adjusting the
working attachment fitted to the tool.
-
Before using the tool, make sure that a
hut o device has bee fitted to the
Recommended
Air
Supply
System
supply line and the position is known
Figure
1
Page No
1