Filter
Top Products
Form
#
ZCE567A
Model
5979A
118"
(3
rnm)
Pencil Air Die Grinder
ManufacturerISupplier
Sioux Tools, Inc.
250 Snap-on Drive
P.O. Box 1596
Murphy, NC 28906
Operator Instructions
Includes
-
Foreseen Use,
Work
Stations, Putting Into Service,
Operating, Dismantling, Assembly and Safety Rules.
Product Type
RPM
118"
(3
mm)
Pencil
Cycles
Per
~m
Air Die Grinder
Important
Read these instructions carefully before installing, operating,
servicing or repairing this tool. Keep these instructions in a safe
accessible place.
U.S.A.
Tel No. 828-835-9765
Fax No. 828-835-9685
1
5979A
Model No/Nos
I
Serial No.
Air Pressure
Product Net Weight
0.44
Ibs
0.20
Kg
Recommended Working
6.2
bar
90
PSI
Maximum
6.2
bar
90
PSI
Recommended Use Of
Balancer Or Support
NO
Test Method:
Tested in accordance with Pneurop
test code PN8NTC1 and IS0 Standard 3744
Recommended Hose Bore
Size
-
Minimum
5/16
ins
8
mm
SAFETY MESSAGES
Personal
Safety
Equipment
Use
-
Safety
lasses
YES
Use
-
Safety Gloves
YES
Use
-
Safety Boots
Use
-
Breathing Masks
YES
Use
-
Ear Protectors
YES
Recommended Max.
Hose Length
30Ft
10M
A
WARNING
Always
Read
Instructions
Before
Using
Power Tools
Noise Level:
Sound Pressure Level 72.0 dB(A)
Sound Power Level 84.0 dB(A)
@
Always Wear
Safety
Goggles
@
Wear
Hearing
Protection
Avoid
Prolonged
Exposure
To
Vibration
Safety rules when using
5979A
pencil Die Grinder
-Use accessories rated at least
70,000
RPM.
-
Prolonged exposure to vibration may cause injury.
-Read all instructions before using this tool. All
operators must be fully trained in its use and aware of
these safety rules.
-
Do not exceed the maximum working air pressure.
-
Use personal protection equipment as recommended.
-
Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities contains
chemicals known to cause cancer, birth defects and other
reproductive harm.
-Use only compressed air at the recommended
conditions.
-If the tool appears to malfunction, remove from use
immediately and arrange for service
Vibration Level
2.0
Meters
/
Sec2
Test Method:
Tested in accordance with IS0
standards 8662 Parts 1
&
13
chance of coming into contact with live electricity.
-
Always when using the tool, adopt a firm footing and/or
position and grip the tool sufficiently only to overcome
any reaction forces that may result from the tool doing
work. Do not overgrip.
-Use only correct spare parts for maintenance and
repair. Do not improvise or make temporary repairs.
Major servicing and repairs should only be carried out
by persons trained to do so.
-
Do not lock, tape, wire, etc. the 'On/Off9 valve in 'On'
position. The triggerllever, etc. must always be free to
return to the 'Off' position when released.
-Always shut off the air supply to the tool and press the
'OnIOff valve to exhaust the air from the feed hose
before fitting, removing or adjusting the working
attachment fitted to the tool.
-
Before using the tool, make sure that a shut off device
and repair. If it is not practical to
remove tool from service, then shut
off the air supply to the tool and write
or have written a warning note and
attach it to the tool.
-
If tool is to be used with a balancer or
other suspension device, ensure that
the tool is firmly attached to the
Easy
To
Reach
And
Air
Tool
suspensionlsupport device.
Operate
Shut
Off
Valve
-When operating the tool, always keep
the body and particularly the hands
away from the working attachment
fixed to the tool.
-The tool is not electrically insulated.
Never use the tool if there is any
Page No
1