Filter
Top Products
i. Pry off the battery cover by a clip.
(Diagram 1).
ii. Insert a 9V alkaline battery to the
connector wire and place the battery
inside the battery compartment.
(Diagram 2)
iii. Slide the battery cover back on.
iv.Straight up the antenna wire in
vertical position (Diagram 3).
v. Turn on the unit by sliding the power
switch to ON position. (Diagram 4)
The repeater is now ready to operate.
Put the repeater in your desired location,
preferably at least 3 feet above the
ground and centrally located between the
furthest sensors and the receiver unit
with which it communicates. To obtain the
best performance, the environment
around the repeater you placed should
not be near any other wireless devices in
order to avoid interference.
2. INSTALLATION
1. INTRODUCTION
Skylink
®
Repeater
Model RP-318
The Skylink Repeater model RP-318 is designed to increase the range of
Skylink Household Alert sensors by boosting and repeating signal from
sensors to receiver unit.
In this package, you should find a Repeater and an adapter.
Please follow the instructions below to setup your Repeater.
3. EXTERNAL POWER - DC 12V
The repeater can be powered by
either 9V battery or external AC
power adapter. Simply plug in the
AC adapter to the position ‘DC
JACK’ and then turn on the power
will make the repeater work.
(Diagram 5).
5. WARRANTY
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful inter-
ference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment dose cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
4. FCC
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com (Reply within 24 hrs)
http://www.skylinkhome.com
P/N. 101A317 Rev.0
©2004 SKYLINK GROUP
If you would like to order Skylink’s products or have difficulty getting them to
work, please :
1. visit our FAQ section at www.skylinkhome.com , or
2. email us at support@skylinkhome.com (reply within 24 hrs), or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax +800 286-1320
6. CUSTOMER SERVICE
Diagram 1
Diagram 2
Diagram 3
Diagram 5
Diagram 4
Repeater
POWER UP
LOCATION
Activate your existing Skylink Household Alert sensor to transmit the
signal in front of the repeater. The distance between the sensor and the
repeater should be at least 1 to 2 feet. When the repeater receives and
repeats the signal, the red light on the repeater will flash.
Note: When repeating signals, some delay in responding may be evident.
TESTING
Clip
Adapter