Southbend SB1038F Lathe User Manual


  Open as PDF
of 4
 
Manual Insert
PHONE: (360) 734-1540 • www.southbendlathe.com
MODEL SB1038F
16" X 40" LATHE 440V w/DRO
Copyright © June, 2011 by South Bend Lathe Co.
WARNING: No portion of this manual may be reproduced without written approval.
#BL14238 Printed in USA
The Model SB1038F Lathe is the same machine as the Model SB1038 except for the following:
• Addeda2-AxisFagorDigitalReadout(DRO).
Exceptforthedifferencesnotedinthisinsert,allothercontentintheModelSB1038Owner’sManual
appliestothismachine.Beforeoperatingyournewlathe,youMUSTreadandunderstandthisinsert,
theentireModelSB1038Owner’sManual,andtheFagorDROOwner’sManualtoreducetheriskof
injurywhenusingthismachine.Keepthisinsertforlaterreference.
IfyouhaveanyfurtherquestionsaboutthismanualinsertorthedifferencesbetweentheModel
SB1038FandtheModelSB1038,contactourTechnicalSupportat(360)734-1639oremail
sales@southbendlathe.com.
REF PART # DESCRIPTION REF PART # DESCRIPTION
2318 PSB1037F2318 DRO ASSEMBLY FAGOR 2-AXIS 2318-3 PSB1014F2318-3 DRO Y-AXIS SCALE FAGOR MKT-27
2318-1 PSB1014F2318-1 DRO DISPLAY FAGOR 20-iT 2407 PSB1038F2407 MACHINE ID LABEL
2318-2 PSB1037F2318-2 DRO X-AXIS SCALE FAGOR MKT-102 2416 PSB1038F2416 MODEL NUMBER LABEL
New & Changed Parts
MODEL SB1038F
16" x 40" EVS
TOOLROOM LATHE
w/DIGITAL READOUT
TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY WHILE USING THIS
MACHINE:
WARNING!
!
Motor: 7.5HP, 440V, 3-Ph, 60Hz
Full Load Amp Draw 10.75A
Swing Over Bed: 16.14"
Distance Between Centers: 40"
Swing Over Cross Slide: 10.375"
Swing Over Gap: 22.95"
Spindle Nose to Gap (max.): 6.5"
Cross Slide Travel: 9"
Compound Travel: 5.1"
Spindle Nose: D1-6 Camlock
Spindle Bore: 2-1/16"
Spindle Taper: MT#6
Tailstock Taper: MT#4
Weight: 3080 lbs.
1. Read and understand manual before starting.
2. Always wear approved eye protection.
3. Make sure the machine is connected to a grounded power source.
4. Keep all guards in place.
5. DO NOT wear loose clothing, gloves, or jewelry; secure long hair and
roll up long sleeves.
6. Disconnect power before service, maintenance, or adjustments.
7. DO NOT operate when tired or under the influence of drugs or alcohol.
8. Make sure the machine is properly adjusted/set up before starting.
9. Change cutting fluid regularly and avoid contact with skin.
10. Make sure workpiece is properly and securely held in the chuck and has
safe clearance through full rotation before starting the lathe.
11. Never leave the chuck key in the chuck.
12. Never touch the chuck or workpiece when it is in motion.
13. Never leave the lathe running unattended.
14. Make sure long workpieces are properly supported.
15. Always use the proper speed rate for the material you are turning.
16. Do not allow children to have unsupervised access to the machine.
2416
2407
2318
2318-1
2318-3
2318-2
next