3M 51210 Sander User Manual


  Open as PDF
of 6
 
3M™ 5 in & 6 in Random Orbital Sander 3 Revision 051210 3M™ 5 in & 6 in Random Orbital Sander 4 Revision 051210
Parts List
Product Configuration/Specifications: 12,000 RPM Random Orbital Sander
† Available only in Europe.
‡ Available only in APAC.
* Declared noise levels; measurements carried out in accordance with standard EN ISO 15744:2008.
** Declared vibration levels in accordance with EN12096; measurements carried out in accordance with standard EN ISO 8662-8:1997.
IMPORTANT NOTE: The noise and vibration values stated in the table are from laboratory testing in conformity with stated codes and
standards and are not sufficient risk evaluation for all exposure scenarios. The actual exposure values and amount of risk or harm
experienced to an individual is unique to each situation and depends upon the surrounding environment, the way in which the individual
works, the particular material being worked, work station design, as well as upon the exposure time and the physical condition of
the user. 3M™ cannot be held responsible for the consequences of using declared values instead of actual exposure values for any
individual risk assessment.
Item 3M Part Number UPC Description Qty.
1 A0040 28113 EXTERNAL RETAINING RING 1
2 A0021 28107 BEARING - 2 SHIELDS 1
3 B0017 28173 REAR ENDPLATE 1
4 A0005 28094 CYLINDER ASSEMBLY 1
5 A0042 28115 5 mm x 2 mm O-RING 1
6 B0005 28170 ROTOR 1
7 A0010 28099 VANE 5
8 A0041 28114 WOODRUFF KEY 1
9 B0016 28172 FRONT ENDPLATE 1
10 A0019 28106 BEARING - 2 SHIELDS 1
11 A0045 28118 39.4 mm x 3.1mm O-RING 1
12 A0001 28093 LOCK RING 1
13 B0279 28180 5 in x 3/32 in ORBIT SHAFT BALANCER 1
B0277 28178 5 in x 3/16 in ORBIT SHAFT BALANCER 1
B0348 30325 5 in x 5/16 in (8.0 mm) ORBIT ROS BALANCER 1
B0278 28179 6 in x 3/16 in ORBIT SHAFT BALANCER 1
B0280 28181 6 in x 3/32 in ORBIT SHAFT BALANCER 1
B0334 28184 6 in x 5/16 in (8 mm) ORBIT SHAFT BALANCER 1
14 A0122 28132 FILTER 1
15 A0121 28131 DUCKBILL CHECK VALVE 1
16 A0120 28130 VALVE RETAINER 1
17 N/A N/A N/A 1
18 A0938 28148 DOUBLE ROW ANGULAR CONTACT BEARING - SEAL 1
19 A0016 28103 SPACER 12.1 mm ID x 18.0 mm OD x 0.2 mm THK 1
20 A0017 28104 BELLEVILLE WASHER 1
21 A0018 28105 RETAINING RING 1
22 B0018 28174 SPINDLE 1
23 A1351 28163 LEVER FOR 2.5 mm (3/32 in) ORBIT 1
A1352 28164 LEVER FOR 5.0 mm (3/6 in) ORBIT 1
A1447 28169 LEVER FOR 8 mm (5/6 in) ORBIT 1
24 A0031 28109 LEVER SPRING PIN 1
25 20342 20342 GRIP 2.5 in OPT
20343 20343 GRIP 2.75 in 1
20344 20344 GRIP 3 in OPT
26 A0015 28102 VALVE SLEEVE 1
27 A1330 28150 HOUSING 1
28 A0008 28097 VALVE STEM ASSEMBLY 1
29 A0043 28116 9.0 mm x 1.5 mm O-RING 1
30 B0014 28171 SPEED CONTROL 1
31 A0039 28112 INTERNAL RETAINING RING 1
32 A1346 28158 5/6 in NON-VACUUM SHROUD 1
33 A1347 28159 5/6 in SHROUD 1
A1348 28160 Ø 6 In CLEAN SANDING ROS DISC PAD SHROUD 1
35 A0022 28108 24 mm PAD WRENCH 1
36 N/A N/A DISC PAD SUPPLIED WITH EACH TOOL (TYPE DETERMINED BY MODEL) 1
37 A0062 28121 INTERNAL MUFFLER 1
38 A0068 28122 MUFFLER INSERT 1
39 A0166 28138 MUFFLER HOUSING 1
40 A0009 28098 VALVE SEAT 1
41 A0007 28096 VALVE 1
42 A0014 28101 VALVE SPRING 1
43 A0013 28100 INLET BUSHING ASSEMBLY 1
44 A0044 28117 14 mm x 1.5 mm O-RING 2
45 A0006 28095 SGV RETAINER 1
46 A0778 28146 1 in/28 mm HOSE SEAL 1
47 A1338 28156 ASSEMBLY FOR 1 in/28 mm HOSE SGV SWIVEL EXHAUST FITTING 1
48 N/A N/A TAG W/ INSTRUCTION FOR 1 in/28 mm HOSE SEAL 1
49 N/A N/A 3/4 in/19 mm HOSE SEAL N/A
50 N/A N/A ASSEMBLY FOR 3/4 in/19 mm HOSE SGV SWIVEL EXHAUST FITTING N/A
51 A1333 28153 SGV SKIRT/SHROUD ADAPTER 1
52 28301 28301 VACUUM HOSE, 1 in ID x 6 ft OPT
53 28302 28302 VACUUM HOSE ADAPTOR, 1 in Internal Hose Thread OPT
54 A1343 28157 ASSEMBLY FOR ROS CV 1 in/28 mm SWIVEL EXHAUST 1
55 A0048 28120 FLANGED NUT 1
56 A1345 28157 ASSEMBLY FOR ROS CV 3/4 in. SWIVEL EXHAUST OPT
57 A0047 28119 WASHER 1
58 A0769 28145 SCREW 1
59 A1434 28303 VACUUM BAG COVER (CLOTH) OPT
60 20338 20338 VACUUM BAG INSERT (PAPER) OPT
61 20452 20452 CLEAN SANDING FILTER BAG 1
62 20453 20453 FILTER BAG ADAPTOR 1
63 20341 20341 VACUUM HOSE FITTING ADAPTOR, 1 in Internal Hose Thread x 1-1/2 in OD Hose Adpator OPT
64 20209 20209 RANDOM ORBITAL SANDER AIR LINE EXTENSION, 3/8 in x 4 ft OPT
Operating / Maintenance Instructions
PRIOR TO THE OPERATION
The tool is intended to be operated as a hand held tool. It is always recommended that while using the tool, operators stand on a
solid oor, in a secure position with a rm grip and footing. Be aware that the sander can develop a torque reaction. See the section
“SAFETY PRECAUTIONS”.
Use a clean lubricated air supply that will give a measured air pressure at the tool of 6.2 bar (90 psig) when the tool is running with
the lever fully depressed. It is recommended to use an approved 10 mm (3/8 in) x 8 m (25 ft) maximum length airline. Connect the tool
to the air supply as shown in Figure 1. Do not connect the tool to the airline system without an easily accessible air shut off valve. It is
strongly recommended that an air lter, regulator and lubricator (FRL) be used as shown in Figure 1as this will supply clean, lubricated
air at the correct pressure to the tool. In any case appropriate air pressure regulators shall be used at all times while operating this
tool where the supply pressure exceeds the marked maximum of the tool. Details of such equipment can be obtained for your tool
distributor. If such equipment is not used, the tool should be manually lubricated. To manually lubricate the tool, disconnect the airline
and put 2 to 3 drops of suitable pneumatic motor lubricating oil such as 3M™ Air Tool Lubricant PN 20451, Fuji Kosan FK-20, Mobil
ALMO 525 into the hose end (inlet) of the tool. Reconnect tool to the air supply and run tool slowly for a few seconds to allow air to
circulate the oil. If the tool is used frequently, lubricate it on a daily basis or lubricate it if the tool starts to slow or lose power. It is
recommended that the air pressure at the tool be 6.2 bar (90 psig) while the tool is running so the maximum RPM is not exceeded. The
tool can be run at lower pressures but should never be run higher than 6.2 bar (90 psig). If run at lower pressure the performance of
the tool is reduced.
Note: All Vacuum machines use Ø 28 mm (1 in.) Vacuum Hose Fittings.
Orbit Pad Face
Vacuum
Type
Pad Type
Pad Size
mm (in)
Model
Number
Pad Part
Number
Product Net Wt
kg (lb)
Height mm
(in)
Length mm
(in)
*Noise Level
dBA Pressure
(Power)
**Vibration
Level m/s
2
(ft/s
2
)
**Uncertainty
K
m/s
2
2.5 mm
(3/32 in)
Stikit™
Non
Vacuum
Low Prole
127 (5) 20320 20351 0.72 (1.59) 82.9 (3.26) 148.4 (5.84) 77 (83) 3.1 (10.2) 1.55
150 (6) 20328 20354 0.76 (1.68) 82.9 (3.26) 161.1 (6.34) 83 (89) 3.3 (10.8) 1.65
Hookit™
Central
Vacuum
Clean
Sanding
127 (5) 20321 20353 0.78 (1.72) 84.5 (3.33) 209.5 (8.25) 77 (83) 3.1 (10.2) 1.55
150 (6) 20329 20356 0.83 (1.83) 84.5 (3.33) 222.2 (8.75) 83 (89) 3.3 (10.8) 1.65
150 (6)
20463‡
20465 0.83 (1.83) 84.5 (3.33) 222.2 (8.75) 83 (89) 3.3 (10.8) 1.65
Self-Gen
Vacuum
Clean
Sanding
127 (5) 20322 20353 0.80 (1.76) 84.5 (3.33) 217.9 (8.58) 84 (95) 3.1 (10.2) 1.55
150 (6) 20330 20356 0.86 (1.90) 84.5 (3.33) 230.6 (9.08) 83 (92) 3.1 (10.2) 1.55
150 (6)
20464‡
20465 0.86 (1.90) 84.5 (3.33) 230.6 (9.08) 83 (92) 3.1 (10.2) 1.55
5 mm
(3/16 in)
Stikit™
Non
Vacuum
Low Prole
127 (5) 20317 20351 0.75 (1.65) 82.9 (3.26) 149.6 (5.89) 80 (88) 3.2 (10.5) 1.60
150 (6) 20325 20354 0.79 (1.74) 82.9 (3.26) 162.3 (6.39) 79 (83) 3.3 (10.8) 1.65
Hookit™
127 (5)
20457‡
20352 0.75 (1.65) 82.9 (3.26) 149.6 (5.89) 80 (88) 3.2 (10.5) 1.60
150 (6)
20460‡
20355 0.79 (1.74) 82.9 (3.26) 162.3 (6.39) 79 (83) 3.3 (10.8) 1.65
Hookit™
Central
Vacuum
Clean
Sanding
127 (5) 20318 20353 0.81 (1.79) 84.5 (3.33) 210.8 (8.30) 81 (88) 3.2 (10.5) 1.60
150 (6) 20326 20356 0.86 (1.90) 84.5 (3.33) 223.5 (8.80) 77 (85) 3.3 (10.8) 1.65
150 (6)
20461‡
20465 0.86 (1.90) 84.5 (3.33) 223.5 (8.80) 77 (85) 3.3 (10.8) 1.65
Stikit™ Low Prole
127 (5)
20455‡
20442 0.81 (1.79) 84.5 (3.33) 210.8 (8.30) 81 (88) 3.2 (10.5) 1.60
150 (6)
20458‡
20454 0.86 (1.90) 84.5 (3.33) 223.5 (8.80) 77 (85) 3.3 (10.8) 1.65
Stikit™
Self-Gen
Vacuum
Low Prole
127 (5)
20456‡
20442 0.83 (1.83) 84.5 (3.33) 219.2 (8.63) 85 (93) 3.2 (10.5) 1.60
150 (6)
20459‡
20454 0.89 (1.96) 84.5 (3.33) 231.9 (9.1) 83 (92) 3.3 (10.8) 1.65
Hookit™
Self-Gen
Vacuum
Clean
Sanding
127 (5) 20319 20353 0.83 (1.83) 84.5 (3.33) 219.2 (8.62) 85 (93) 3.2 (10.5) 1.60
150 (6) 20327 20356 0.89 (1.96) 84.5 (3.33) 231.9 (9.1) 83 (92) 3.3 (10.8) 1.65
150 (6)
20462‡
20465 0.89 (1.96) 84.5 (3.33) 231.9 (9.1) 83 (92) 3.3 (10.8) 1.65
8 mm
(5/16 in)
Stikit™
Non
Vacuum
Low Prole
127 (5)
20253 20351 0.76 (1.68) 82.9 (3.26) 150.37 (5.92) 74 (83)) <2.5 (<8.2) N/A
Hookit™
Central
Vacuum
Clean
Sanding
20254/
†63378
20353
0.82 (1.81) 82.9 (3.26) 212.08 (8.35) 77 (85) <2.5 (<8.2) N/A
Self-Gen
Vacuum
20255/
†63379
0.84 (1.85) 82.9 (3.26) 220.66 (8.68) 91 (99) <2.5 (<8.2) N/A
Stikit™
Non
Vacuum
Low Prole
150 (6)
20324 20354 0.79 (1.74) 82.9 (3.26) 163.42 (6.45) 77 (85) 3.3 (10.8) 1.65
Hookit™
Central
Vacuum
Clean
Sanding
20213 20356 0.87 (1.92) 82.9 (3.26) 224.8 (8.85) 75 (85) 3.5 (11.4) 1.75
63373† 20465 0.87 (1.92) 82.9 (3.26) 224.8 (8.85) 75 (85) 3.5 (11.4) 1.75
Self-Gen
Vacuum
20208 20356 0.90 (1.98) 82.9 (3.26) 233.4 (9.18) 82 (92) 3.4 (11.1) 1.70
63372† 20465 0.90 (1.98) 82.9 (3.26) 233.4 (9.18) 82 (92) 3.4 (11.1) 1.70
 previous next