AMX NXA-BASE/B Battery Charger User Manual


  Open as PDF
of 2
 
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
12/08
©2008 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-2255 REV: E
Checking the NXT-BP Charge
1. Press the Battery Life Indicator button (FIG. 5) once to illuminate the
Battery Life LEDs and display the percent charge remaining on the
battery (this indication lasts for a few seconds).
2. Repeat the above step for the remaining NXT-BP battery.
3. Charge the batteries by inserting them within the battery base.
It is recommended to fully charge the batteries before they are initially
inserted into the base. Refer to the following section for more detailed
information on this process.
ATTENTION! If the 25% LED indicator is blinking, this indicates that the
battery has less than 5% of a charge remaining.
Installation of an NXT-BP into the NXA-BASE/B
The base does not directly connect to a power supply, but rather receives the
power necessary to charge the batteries from the Modero panel (through the
Panel Interface connector).
1. With the panel atop the base, open the battery compartment (FIG. 6) by
pulling the handle outwards. This compartment is capable of housing two
(2) NXT-BP batteries.
2. Install the NXT-BP battery with the "label-side" facing down
3. Align the battery connectors with their corresponding battery connector
ports (located on the battery slot inside the battery compartment) (FIG. 6).
4. Insert the NXT-BP battery until the connectors securely fit into the battery
connector port within the slot.
5. Repeat steps 3 and 4 for the remaining battery.
6. Apply a small amount of pressure to close the battery compartment until
the compartment latches.
ATTENTION! The AMX logo will appear to indicate that the panel is
receiving power.
Updating Firmware and Setup pages
1. Download the latest Modero firmware from the AMX.com website.
2. Update the latest firmware to the Modero panel. Refer to the instruction
manual for detailed download and update instructions.
NOTE: With older panels, such as the NXDT-CV7, -CV10, or -CV17 touch
panels, the Modero firmware must be Build 27 or higher.
3. Download the TPDesign4 setup patch from the AMX.com website to
update the current release of TPD4 for use with the NXA-BASE/B.
4. Launch the patch TPD4 Patch.EXE to update your TPD4 program.
5. After rebooting your machine, create a new TPD4 project that consists of
a single blank NXT Modero touch panel page and button.
6. Download this page to the panel using the Full Clean - Download to Panel
feature in TPD4. Refer to the manual for more detailed information. This
step updates the Setup pages (more specifically, the Battery Base page)
on your Modero panel.
7. Press and hold the Front Setup Access button (FIG. 7) for 3-seconds to
access the on-screen Setup page.
8. Press the on-screen Protected Setup button and press the on-screen
Reboot button to restart the panel and incorporate the new changes.
9. After startup, repeat step 7 to access the Setup page.
10. Press the on-screen BATTERY BASE button to access the Battery Base
page. This page allows you to both confirm communication between the
two units (panel and battery base) and the charging/discharging status of
the batteries within the battery base.
Charging the NXT-BPs using the NXA-BASE/B
1. Insert the two (2) batteries into the battery compartment shown in FIG. 6.
2. Insert a 2-pin connector, from a PSN6.5 power supply, to the rear PWR
connector on the NXT Modero panel.
FIG. 4 NXT-BASE/B showing underside fastener locations
FIG. 5 NXT-BP Modero Power Pack (showing Battery Life Indicator and button)
FIG. 6 Battery installation procedure
Captive fasteners
(secure base to
panel)
Battery Life Indicator
Battery Life (Charge)
button
It’s recommended to
fully charge the
batteries before their
initial use
Battery
Compartment
NXT-BP Battery #2
Battery
Connectors
Battery
Connector
Port
Interface
connector
FRONT
NXT-BP Battery #1
FIG. 7 NXA-BASE/B and Modero panel combo
Front Setup
Access button
(simulated image)
 previous