Filter
Top Products
•
Selection of arbor. Select the proper arbor for the holesaw
size and your power drill. If the arbor has drive pins, make
sure they are engaged. For arbors with drive pins, slide pin
ring back, screw holesaw onto arbor to shoulder, and push
ring with pins into holesaw while backing off holesaw if
necessary.
•
Feed rate. Maintain positive feed rate, and always start
cutting square to the workpiece.
•
Removal of chips. Chip removal is extremely important.
Withdraw holesaw intermittently to prevent clogging.
•
Operation speed. The cutting speeds recommended can
be found in the instructions leaflet in the Holesaw Sets.
Variations from these recommendations may be chosen
from your own experience.
•
Lubricants. Always use a lubricant when cutting metal,
as this increases the life of the holesaw.
General directions for use
EAN code: 731151 8044985
Holesaws
3830-16-VIP 16 mm 5/8"
3830-22-VIP 22 mm 7/8"
3830-25-VIP 25 mm 1"
3830-29-VIP 29 mm 1 1/8"
3830-32-VIP 32 mm 1 1/4"
3830-41-VIP 41 mm 1 5/8"
3830-51-VIP 51 mm 2"
3830-73-VIP 73 mm 2 3/4"
3830-83-VIP 83 mm 3 1/4"
Arbors
3834-ARBR-930
– for holesaws 14 – 30 mm
3834-ARBR-9100 (PD type)
– for holesaws 30 – 100 mm
Set 3834-SET-92
EAN code: 731151 8166458
Holesaws
3830-16-VIP 16 mm 5/8"
3830-19-VIP 19 mm 3/4"
3830-25-VIP 25 mm 1"
3830-30-VIP 30 mm 1 3/16"
3830-35-VIP 35 mm 1 3/8"
3830-41-VIP 41 mm 1 5/8"
3830-51-VIP 51 mm 2"
3830-67-VIP 67 mm 2 5/8"
Arbors
3834-ARBR-1130
– for holesaws 14 – 30 mm
3834-ARBR-11152 (PD type)
– for holesaws 30 – 210 mm
Set 3834-SET-94
EAN code: 731151 8159894
Holesaws
3830-16-VIP 16 mm 5/8"
3830-19-VIP 19 mm 3/4"
3830-22-VIP 22 mm 7/8"
3830-29-VIP 29 mm 1 1/8"
3830-35-VIP 35 mm 1 3/8"
3830-44-VIP 44 mm 1 3/4"
3830-52-VIP 52 mm 2 1/16"
3830-57-VIP 57 mm 2 1/4"
3830-64-VIP 64 mm 2 1/2"
Arbors
3834-ARBR-1130
– for holesaws 14 – 30 mm
3834-ARBR-11152 (PD type)
– for holesaws 30 – 210 mm
3834-DRL
Set 3834-SET-95
Space prepared for 3 extra holesaws
PCS
MM INCH
from to from to
1 x 19 20
3/4 25/32
1 x 32 35
1 1/4 1 3/8
1 x 37 40
1 7/16 1 9/16
Space prepared for 3 extra holesaws
PCS
MM INCH
from to from to
1 x 32 –
1 1/4 –
1 x 37 40
1 7/16 1 9/6
1 x 37 83
1 7/16 3 1/4
Space prepared for 3 extra holesaws
PCS
MM INCH
from to from to
1 x 19 25
3/4 1
1 x 32 –
1 1/4 –
1 x 37 40
1 7/16 1 9/6
07-0016_Holesaws_UK 07-05-21, 14.047