Filter
Top Products
98
OPERATION
Using Keyless Chucks (Fig. 5)
Your cordless tool is equipped with a spindle
lock that allows the chuck to be tightened
with one hand.
Always remove the battery pack or lock
the trigger before inserting or removing bits.
1. To open the chuck jaws, turn the sleeve
in the "OPEN" direction indicated on
the chuck.
When using drill bits, allow the bit to
strike the bottom of the chuck. Center
the bit in the chuck jaws and lift it about
1/16" off of the bottom.
When using screwdriver bits, insert
the bit far enough for the chuck jaws
to grip the hex of the bit.
2. To close the chuck jaws, turn the
sleeve in the "CLOSE" direction indi-
cated on the chuck. The bit is secure
when the chuck makes a ratcheting
sound and the sleeve can not be ro-
tated any further.
NOTE: A ratcheting sound may be heard
when the chuck is opened or closed. This
noise is part of the locking feature, and
does not indicate a problem with the chuck's
operation.
WARNING!
To reduce the risk of injury, wear
safety goggles or glasses with
side shields.
Fig. 5
Sleeve
The torque specifications shown here are
approximate values obtained with a fully
charged battery pack.
Using Clutch (Fig. 6)
This tool has an adjustable clutch for driv-
ing different types of screws into differ-
ent materials. When properly adjusted, the
clutch will slip at a preset torque to pre-
vent driving the screw too deep and to
prevent damage to the screw or tool.
To adjust the clutch, turn the torque selec-
tor collar to one of the twenty positions
shown on the collar. The number must line
up with the arrow on top of the tool.
Fig. 6
Torque
selector
collar
Position
numbers
NOTE: Because the above settings are only
a guide, use a piece of scrap material to
test the different clutch positions before
driving screws into the workpiece.
Open
Close
Positions
1 - 5
6 - 10
11 - 15
16 - 20
Drill
Low
High
0 - 10 in. lbs.
12 - 21 in. lbs.
24 - 32 in. lbs.
35 - 44 in. lbs.
280 in. lbs.
80 in. lbs.
0602-20
0 - 10 in. lbs.
12 - 21 in. lbs.
24 - 32 in. lbs.
35 - 44 in. lbs.
390 in. lbs
100 in. lbs.
0612-20
Torque
Torque
WARNING!
ASSEMBLY
Always remove battery pack
before changing or removing ac-
cessories. Only use accessories
specifically recommended for this
tool. Others may be hazardous.
Clip-Lok
TM
System (Fig. 3 & 4)
The Clip-Lok system consists of three
pieces; the belt clip, the tool holder, and the
bit holder.
The system is shipped assembled for right-
handed use. To change the assembly for
left-handed use:
1. Remove battery pack.
2. Remove screws holding the tool holder
and the bit holder.
3. Lift the holders at the narrow end and
pull the front tangs out of their slots.
4. Replace the pieces onto the desired
side by sliding the tangs into the slots.
Tighten the screws securely.
Fig. 3
Attaching the Belt Clip
(Fig. 4)
Fig. 4
The belt clip can be mounted to tool belts,
bags, buckets, etc. To mount the belt clip:
1. Push and hold the clamp release lever.
2. Pull out the clamp at the back of the
belt clip and release the clamp release
lever.
3. Slide the clamp over the desired tool
belt, bag, bucket, etc.
4. Press in the clamp to achieve the de-
sired tightness.
Using the Clip-Lok Tool Holder
1. To attach the tool to the belt clip, slide
the tool holder over the stud on the
belt clip until it is held in place by the
protruding pin.
2. To release the tool from the belt clip,
grasp the tool handle, push down on
the tool release lever with your thumb,
and pull up on the tool.
Using the Clip-Lok Bit Holder
The bit holder holds two standard 1/4" hex
shank bits up to two inches long.
1. Insert the bit by pressing it into the
clip.
2. Remove the bit by lifting the tip of the
bit and pulling it out of the clip.
Belt clip
Bit holder
Tool holder
Front tangs
Stud
Tool
release lever
Pin
Clamp
Clamp release
lever