Filter
Top Products
-10-
&37*$&
3&7&/5*7&."*/5&/"/$&
1&3'03.&%#:6/"65)03*;&%
1&340//&-.":3&46-5*/.*41-"$*/(0'
*/5&3/"-8*3&4"/%$0.10/&/548)*$)
$06-% $"64& 4&3*064 )";"3% We
recommend that all tool service be
performed by a Bosch Factory Service
Center or Autho rized Bosch Service Station.
Your Bosch tool has been properly lubricated
and is ready to use. It is recommended that
tools with gears be regreased with a special
gear lubricant at every brush change.
The brushes and commutator in your tool
have been engineered for many hours of
dependable service. To maintain peak
efficiency of the motor, we recommend every
two to six months the brush es be examined.
Only genuine Bosch replace ment brushes
specially designed for your tool should be
used.
After about 300-400 hours of operation, or at
every second brush change, the bearings
should be replaced at Bosch Factory Service
Center or Au thorized Bosch Service Station.
Bearings which become noisy (due to heavy
load or very abrasive material cut ting) should
be replaced at once to avoid overheating or
motor failure.
-&"/*/(
0"70*%"$$*%&/54"-8":4
%*4$0//&$55)&500-'30.
5)&108&34611-:#&'03&$-&"/*/(03
1&3'03.*/("/:."*/5&/"/$&The tool may
be cleaned most effectively with compressed
dry air. -8":48&"34"'&5:(0((-&48)&/
$-&"/*/(500-48*5)$0.13&44&%"*3
Ventilation openings and switch levers must
be kept clean and free of foreign matter. Do
not at tempt to clean by inserting pointed
objects through openings.
&35"*/$-&"/*/("(&/54
"/% 40-7&/54 %"."(&
1-"45*$1"354Some of these are: gasoline,
carbon tetrachlo ride, chlo rinated cleaning
solvents, ammonia and house hold detergents
that contain ammonia.
!
WARNING
!
WARNING
"*/5&/"/$&
!
CAUTION
$$&4403*&4
' "/ &95&/4*0/ $03% *4
/&$&44"3: " $03% 8*5)
"%&26"5&4*;&$0/%6$50345)"5*4$"1"#-&0'
$"33:*/(5)&$633&/5/&$&44"3:'03:063500-
.645#&64&% This will prevent excessive
voltage drop, loss of power or overheating.
Grounded tools must use 3-wire extension
cords that have 3-prong plugs and receptacles.
The smaller the gauge number, the heav i -
er the cord.
!
!
WARNING
Lower die 2 608 639 026
Stop plate
Punch 2 608 639 025
* Side Handle
* Handle Extension
* Hex Key 5/32" (4mm)
(*= standard equipment)
00->4
.1&3&
"5*/(
03%*;&*/
*3&*;&4*/..
3-6
6-8
8-10
10-12
12-16
18 16 16 14 0.75 0.75 1.5 2.5
18 16 14 12 0.75 1.0 2.5 4.0
18 16 14 12 0.75 1.0 2.5 4.0
16 16 14 12 1.0 2.5 4.0 —
14 12 —— ————
25 50 100 150 15 30 60 120
03%&/(5)*/&&5 03%&/(5)*/&5&34
95&/4*0/03%4
BM 1609929Y04 06-10:BM 1609929Y04 06-10 6/14/10 10:14 AM Page 10