Filter
Top Products
-14-
!.6;A2;.;02
&2?C602
"#(&%&%)
$%'&"&$?2C2;A6C2
:.6;A2;.;02=2?3<?:21/FB;.BA5<?6G21
=2?@<;;29:.F?2@B9A6;:6@=9.06;4<3
6;A2?;.9D6?2@.;10<:=<;2;A@D5605
0<B910.B@2@2?6<B@5.G.?1 We recom -
mend that all tool service be performed by a
Bosch Factory Service Center or Authorized
Bosch Service Station. SERVICE MEN:
Disconnect tool and/or charger from power
source before servicing.
''%&
2.92?A3<?/.AA2?F=.08@A5.A.?2;2.?6;4
A526?2;1<39632 If you notice decreased
tool performance or significantly shorter
running time between charges then it is time
to replace the battery pack. Failure to do so
can cause the tool to operate improperly or
damage the charger.
'## (%'#"
Your Bosch tool has been properly lubricated
and is ready for use.
!#'#%&
The motor in your tool has been engineered
for many hours of dependable service. To
maintain peak efficiency of the motor, we
recommend it be examined every six
months. Only a genuine Bosch replacement
motor specially designed for your tool should
be used.
%"&
Bearings which become noisy (due to heavy
load or very abrasive material cutting) should
be replaced at once to avoid overheating and
motor failure.
92.;6;4
'<.C<61.00612;A@.9D.F@
16@0<;;20AA52A<<9.;1<?
05.?42?3?<:A52=<D2?@B==9F/23<?2
092.;6;4 The tool may be cleaned most
effectively with com pressed dry air. 9D.F@
D2.?@.32AF4<4492@D52;092.;6;4A<<9@
D6A50<:=?2@@21.6?
Ventilation openings and switch levers must be
kept clean and free of foreign matter. Do not
attempt to clean by inserting pointed objects
through opening.
<08.D™ # %!"'""
Use dry compressed air to clean dust and
debris from the LockJaw™ blade holder
assembly on a regular basis.
Periodically lubricate LockJaw™ blade
holder with a dry lubricant such as graphite.
2?A.6;092.;6;4.42;A@
.;1 @<9C2;A@ 1.:.42
=9.@A60=.?A@ Some of these are: gasoline,
car bon tetrachloride, chlorinated cleaning
solvents, ammonia and household detergents
that contain ammonia.
!
WARNING
!
WARNING
!
CAUTION
002@@<?62@
3 .; 2EA2;@6<; 0<?1 6@
;202@@.?F . 0<?1 D6A5
.12>B.A2@6G20<;1B0A<?@A5.A6@0.=./92
<30.??F6;4A520B??2;A;202@@.?F3<?F<B?
A<<9 :B@A /2 B@21 This will prevent
excessive voltage drop, loss of power or
overheating. Grounded tools must use 3-
wire extension cords that have 3-prong plugs
and receptacles.
"#' The smaller the gauge number, the
heav i er the cord.
%#!!"&-&#+'"&#"#%&
)# ' '%"'"(%%"''## &
!
WARNING
'<<9I@
:=2?2
%.A6;4
<?1&6G26;*
*6?2&6G2@6;::
3-6
6-8
8-10
10-12
12-16
18 16 16 14 0.75 0.75 1.5 2.5
18 16 14 12 0.75 1.0 2.5 4.0
18 16 14 12 0.75 1.0 2.5 4.0
16 16 14 12 1.0 2.5 4.0 —
14 12 —— ————
25 50 100 150 15 30 60 120
<?1 2;4A56;22A <?1 2;4A56;!2A2?@
(* = standard equipment)
(** = optional accessories)
*1 hour charger
BM 2610027769 09-12_BM 2610027769 09-12.qxp 9/12/12 2:33 PM Page 14