Filter
Top Products
5
“SAVE THESE INSTRUCTIONS”
• Do not allow familiarity gained from frequent use of your miter saw to become commonplace. Always remember that
a careless fraction of a second is sufficient to inflict severe injury.
• THINK SAFETY! SAFETY IS A COMBINATION OF OPERATOR’S COMMON SENSE, KNOWLEDGE OF THE SAFETY AND
OPERATING INSTRUCTIONS AND ALERTNESS AT ALL TIMES WHEN THE MITER SAW IS BEING USED.
THE WARNINGS SHOWN BELOW CAN BE FOUND ON YOUR TOOL. THESE WARNINGS ARE ONLY A
CONDENSED FORM OF THE MORE DETAILED SAFETY RULES AND PRECAUTIONS THAT APPEAR IN
YOUR OWNER'S MANUAL. THEY SERVE AS A REMINDER OF ALL SAFETY RULES NEEDED FOR SAFE OPERATION OF
THIS MITER SAW.
Safety
“READ ALL INSTRUCTIONS” — Failure to follow the SAFETY RULES identified by BULLET (l) symbol listed
BELOW and other safety precautions, may result in serious personal injury.
DESIGNATED DANGER ZONE.
AVOID POSITIONING HANDS,
FINGERS OR ARMS IN THE
AREA DESIGNATED BY THIS
SYMBOL.
A
L
L
E
L
E
C
T
R
I
C
B
R
A
K
E
S
A
W
S
M
A
Y
,
O
N
O
C
C
A
S
I
O
N
,
F
A
I
L
T
O
S
T
O
P
B
L
A
D
E
.
A
F
T
E
R
T
U
R
N
I
N
G
S
A
W
O
F
F
,
A
L
W
A
Y
S
K
E
E
P
S
A
W
I
N
D
O
W
N
P
O
S
I
T
I
O
N
A
N
D
W
A
I
T
F
O
R
B
L
A
D
E
T
O
S
T
O
P
B
E
F
O
R
E
R
E
M
O
V
I
N
G
C
U
T
O
F
F
P
I
E
C
E
S
O
R
C
L
E
A
N
I
N
G
T
A
B
L
E
.
B
R
A
K
I
N
G
A
C
T
I
O
N
O
F
T
H
E
S
A
W
C
A
U
S
E
S
T
H
E
S
A
W
H
E
A
D
T
O
J
E
R
K
D
O
W
N
W
A
R
D
.
B
E
R
E
A
D
Y
F
O
R
T
H
I
S
R
E
A
C
T
I
O
N
W
H
E
N
R
E
L
E
A
S
I
N
G
T
H
E
S
W
I
T
C
H
B
E
F
O
R
E
T
H
E
H
E
A
D
I
S
C
O
M
P
L
E
T
E
L
Y
D
O
W
N
.
WARNIN
G
!
FOR BEVEL OR
COMPOUND CUTS,
MOVE SLIDING
FENCE.
DO NOT OPERATE SAW WITHOUT GUARDS
IN PLACE.
RETURN GUARD TO OPERATING POSITION
AFTER CHANGING THE BLADE.
IF GUARD FAILS TO WORK SMOOTHLY,
STOP SAWING AND SERVICE IT BEFORE
PROCEEDING.
WARNING
!
R
3912 12" (305mm) COMPOUND MITER SAW
120 VOLTS AC ONLY TO 60 Hz
15 AMPS 4000 RPM TYPE 1
DOUBLE INSULATED
READ AND UNDERSTAND
THE OWNER’S MANUAL
BEFORE USING THIS TOOL.
ALWAYS WEAR SAFETY GOGGLES.
TO AVOID ELECTRICAL SHOCK DO NOT EXPOSE
SAW TO RAIN OR USE IN DAMP LOCATIONS.
USE SAW BLADE RATED 4000 RPM OR GREATER.
DISCONNECT SAW FROM POWER SOURCE
BEFORE SERVICING OR CHANGING BLADE.
WHEN SERVICING USE ONLY IDENTICAL
REPLACEMENT PARTS.
S—B Power Tool Co. Chicago, IL Made in Taiwan
LR59053 LISTED
37J2
E82443
R
WARNING
!
WARNIN
G
!
WARNIN
G
!