Filter
Top Products
-4-
overhang of the wheel is too long, the
MOUNTED WHEEL may become loose and
be ejected at high velocity.
,+,120"!*$"! "00,/6"#,/"
" %20"&+0-" 11%" "00,/602 %0
/0&3"4%"")0#,/ %&-0+! / (0
0+!&+$!/2*#,/ / (01"/,/"5 "00
4"/4&/"/20%#,/),,0",/ / ("!4&/"0
#-,4"/1,,),/ "00,/6&0!/,--"!
&+0-" 1#,/!*$",/&+01))+2+!*$"!
"00,/6#1"/&+0-" 1&+$+!&+01))&+$
+ "00,/6 -,0&1&,+ 6,2/0")# +!
601+!"/046#/,*1%"-)+",#1%"
/,11&+$ "00,/6+!/2+1%"-,4"/1,,)
1*5&*2*+,),!0-""!#,/,+"*&+21"
Damaged accessories will normally break apart
during this test time.
"/ -"/0,+) -/,1" 1&3" ".2&-*"+1
"-"+!&+$,+--)& 1&,+20"# "0%&")!
0#"16 $,$$)"0 ,/ 0#"16 $)00"0 0
--/,-/&1"4"/!201*0(%"/&+$
-/,1" 1,/0$),3"0+!4,/(0%,--/,+
-)",#01,--&+$0*))/0&3",/
4,/(-&" "#/$*"+10The eye protection
must be capable of stopping flying debris
generated by various operations. The dust
mask or respirator must be capable of filtrating
particles generated by your operation.
Prolonged exposure to high intensity noise may
cause hearing loss.
""-601+!"/00#"!&01+ "46#/,*
4,/(/"+6,+""+1"/&+$1%"4,/(/"
*2014"/-"/0,+)-/,1" 1&3"".2&-*"+1
Fragments of workpiece or of a broken
accessory may fly away and cause injury
beyond immediate area of operation.
,)!-,4"/1,,)6&+02)1"!$/&--&+$
02/# "0 ,+)6 4%"+ -"/#,/*&+$ +
,-"/1&,+4%"/"1%" 211&+$ "00,/6*6
,+1 1%&!!"+4&/&+$,/&10,4+ ,/!
Cutting accessory contacting a “live” wire may
make exposed metal parts of the power tool
“live” and could give the operator an electric
shock.
)460%,)!1%"1,,)#&/*)6&+6,2/%+!0
!2/&+$1%"01/12- The reaction torque of the
motor, as it accelerates to full speed, can cause
the tool to twist.
0" )*-01,02--,/14,/(-&" "4%"+"3"/
-/ 1& )"3"/%,)!0*))4,/(-&" "&+
,+"%+!+!1%"1,,)&+1%",1%"/%+!
4%&)"&+20" Clamping a small workpiece
allows you to use your hand(s) to control the
tool. Round material such as dowel rods, pipes
or tubing have a tendency to roll while being
cut, and may cause the bit to bind or jump
toward you.
,0&1&,+1%" ,/! )"/,#1%"0-&++&+$
"00,/6If you lose control, the cord may be
cut or snagged and your hand or arm may be
pulled into the spinning accessory.
"3"/)61%"-,4"/1,,)!,4+2+1&)1%"
"00,/6%0 ,*"1, ,*-)"1"01,-
The spinning accessory may grab the surface
and pull the power tool out of your control.
#1"/ %+$&+$1%"&10,/*(&+$+6
!'201*"+10*("02/"1%" ,))"1+21
%2 (,/+6,1%"/!'201*"+1!"3& "0/"
0" 2/")61&$%1"+"!Loose adjustment devices
can unexpectedly shift, causing loss of control,
loose rotating components will be violently
thrown.
,+,1/2+1%"-,4"/1,,)4%&)" //6&+$&1
16,2/0&!"Accidental contact with the
spinning accessory could snag your clothing,
pulling the accessory into your body.
"$2)/)6 )"+1%"-,4"/1,,):0&/3"+10
The motor’s fan will draw the dust inside the
housing and excessive accumulation of
powdered metal may cause electrical hazards.
, +,1 ,-"/1" 1%" -,4"/ 1,,) +"/
#)**)"*1"/&)0Sparks could ignite
these materials.
,+,120" "00,/&"01%1/".2&/")&.2&!
,,)+10Using water or other liquid coolants
may result in electrocution or shock.
& ( (+!")1"!/+&+$0
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, sanding band, brush or
any other accessory. Pinching or snagging
causes rapid stalling of the rotating accessory
which in turn causes the uncontrolled power
tool to be forced in the direction opposite of the
accessory’s rotation.
For example, if an abrasive wheel is snagged
or pinched by the workpiece, the edge of the
wheel that is entering into the pinch point can
dig into the surface of the material causing the
wheel to climb out or kick out. The wheel may
either jump toward or away from the operator,
depending on direction of the wheel’s
movement at the point of pinching. Abrasive
wheels may also break under these conditions.
Kickback is the result of power tool misuse
and/or incorrect operating procedures or
conditions and can be avoided by taking proper
precautions as given below.
BM 2610034444 04-14_DGSH181 4/2/14 11:24 AM Page 4