Filter
Top Products
-10-
(59,&(
5(9(17,9(0$,17(1$1&(
3(5)250(' %< 81$87+
25,=('3(56211(/0$<5(68/7,10,63/$&,1*
2),17(51$/:,5(6$1'&20321(176:+,&+
&28/' &$86( 6(5,286 +$=$5' We
recommend that all tool service be performed
by a Bosch Factory Service Center or Autho -
rized Bosch Service Station.
When the service reminder light lights up or
blinks, this will indicate that the cut-out
carbon brushes will switch off the tool in
approximately 8 hours. After that period, the
light will go off and the tool will stop running.
The tool must then be sent to a service
center for service (Fig. 7).
Your Bosch tool has been properly lubricated
and is ready to use. It is recommended that
tools with gears be regreased with a special
gear lubricant at every brush change.
The brushes and commutator in your tool have
been engineered for many hours of
dependable service. To maintain peak
efficiency of the motor, we recommend every
two to six months the brush es be examined.
Only genuine Bosch replace ment brushes
specially designed for your tool should be used.
Bearings which become noisy (due to heavy
load or very abrasive material cut ting) should
be replaced at once to avoid overheating or
motor failure.
Your tool is designed to provide a qualified
service technician optimal access to replace
the carbon brushes and the cord. This
provides the service technician the ability to
replace these components without the need of
disassembling the entire tool housing.
/($1,1*
2$92,'$&&,'(176$/:$<6
',6&211(&77+(722/)520
7+( 32:(5 6833/< %()25( &/($1,1* 25
3(5)250,1*$1<0$,17(1$1&( The tool may
be cleaned most effectively with compressed
dry air. /:$<6:($56$)(7<*2**/(6:+(1
&/($1,1*722/6:,7+&2035(66('$,5
Ventilation openings and switch levers must be
kept clean and free of foreign matter. Do not
at tempt to clean by inserting pointed objects
through openings.
(57$,1&/($1,1*$*(176
$1' 62/9(176 '$0$*(
3/$67,&3$576 Some of these are: gasoline,
carbon tetrachlo ride, chlo rinated cleaning
solvents, ammonia and house hold detergents
that contain ammonia.
!
WARNING
$,17(1$1&(
!
WARNING
!
CAUTION
Auxiliary Handle*
Carrying case*
(*= standard equipment)
(**= optional accessories)
&&(6625,(6
) $1 (;7(16,21 &25' ,6
1(&(66$5< $ &25' :,7+
$'(48$7(6,=(&21'8&72567+$7,6&$3$%/(
2)&$55<,1*7+(&855(171(&(66$5<)25<285
722/ 0867 %( 86(' This will prevent
excessive voltage drop, loss of power or
overheating. Grounded tools must use 3-wire
extension cords that have 3-prong plugs and
receptacles.
The smaller the gauge number, the
heav i er the cord.
#!
!
WARNING
22/@6
03(5(
$7,1*
25',=(,1
,5(,=(6,100
3-6
6-8
8-10
10-12
12-16
18 16 16 14 0.75 0.75 1.5 2.5
18 16 14 12 0.75 1.0 2.5 4.0
18 16 14 12 0.75 1.0 2.5 4.0
16 16 14 12 1.0 2.5 4.0 —
14 12 —— ————
25 50 100 150 15 30 60 120
25'(1*7+,1((7 25'(1*7+,1(7(56
BM 1609929X76 07-12_1609929X76 07-12.qxp 8/1/12 8:00 AM Page 10