Filter
Top Products
Framing Nailer
Table of Contents
Descripion . . . . . . . . . . . . . . . . . . . . . . .1
Unpacking . . . . . . . . . . . . . . . . . . . . . . .1
Safety Guidelines . . . . . . . . . . . . . . . . .1
Important Safety Information . . . . . . .1
Tool Components and
Specifications. . . . . . . . . . . . . . . . . . . . .2
Operating Instructions . . . . . . . . . . . . .4
Lubrication . . . . . . . . . . . . . . . . . . . . .4
Recommended Hookup. . . . . . . . . . .4
No-Mar Decking Tip. . . . . . . . . . . . . .5
Removing No-Mar Decking Tip. . . . .5
Installing No-Mar Decking Tip . . . . .5
Operational Mode . . . . . . . . . . . . . . .5
Single Cycle Mode . . . . . . . . . . . . . . .5
Bottom Trip Mode . . . . . . . . . . . . . . .5
Mode Conversion. . . . . . . . . . . . . . . .6
Operating A Sequential Trip Tool . . .6
Loading The Tool . . . . . . . . . . . . . . . .6
Unloading The Tool . . . . . . . . . . . . . .6
Adjusting the Nail Penetration. . . . .7
Anti-dry Fire . . . . . . . . . . . . . . . . . . . .7
Adjusting Direction of Exhaust. . . . .7
Clearing A Jam From The Tool . . . . .7
User-Maintenance Instructions . . . . . .7
Fasteners Information . . . . . . . . . . . . .9
Troubleshooting Chart . . . . . . . . . . . . .9
Warranty . . . . . . . . . . . . . . . . . . . . . . .10
Description
This nailer is designed for framing,
trusses, sub-floors, sheathing, exterior
decks, and pallet/create assembly.
Features include: convenient top
loading magazine, no-mar tip,
adjustable exhaust, single cycle trigger,
and an adjustable depth of drive
mechanism.
Model IFN21950
When using tools,
basic precautions
should always be followed, including
the following:
CALIFORNIA PROPOSITION 65
This product or
its power cord may
contain chemicals known to the State
of California to cause cancer and birth
defects or other reproductive harm.
Wash hands after handling.
You can
create
dust when you cut, sand, drill
or grind materials such as
wood, paint, metal, concrete,
cement, or other masonry. This dust
often contains chemicals known to
cause cancer, birth defects, or other
reproductive harm. Wear protective
gear.
Unpacking
After unpacking the unit, inspect
carefully for any damage that may have
occurred during transit.
Make sure to tighten fittings, bolts, etc.,
before putting unit into service.
Safety Guidelines
This manual contains information
that is very important to know and
understand. This information is
provided for SAFETY and to PREVENT
EQUIPMENT PROBLEMS. To help
recognize this information, observe the
following symbols.
Danger indicates an
imminently
hazardous situation which, if not
avoided, WILL result in death or serious
injury.
Warning indicates a
potentially
hazardous situation which, if not
avoided, COULD result in death or
serious injury.
Caution indicates a
potentially
hazardous situation which, if not
avoided, MAY result in minor or
moderate injury.
Notice indicates
important
information, that if not followed, may
cause damage to equipment.
NOTE: Information that requires special
attention.
Important Safety Instructions
INSTRUCTIONS PERTAINING TO A
RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
REMINDER: Keep your dated proof of purchase for warranty purposes!
Attach it to this manual or file it for safekeeping.
IN725400AV 3/08
See Warranty on page 8 for important information about commercial use of this product.
Operating Instructions IFN21950
Locate model and date code on
tool and record below:
Model No.: _____________________
Date Code: _____________________
Retain these numbers for
future reference.
For parts, product & service information
visit www.chpower.com
© 2008 Campbell Hausfeld/Scott Fetzer
Campbell Hausfeld Tools meet or exceed Industries’ Standards as set forth by the American National Standard
Institute/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002.