Filter
Top Products
Page 7For technical questions, please call 1-800-444-3353.SKU 68696
Instructions For Putting Into Use
Read the ENTIRE IMPORTANT SAFETY
INFORMATION section at the beginning
of this manual including all text under
subheadings therein before set up or use of
this product.
TO PREVENT SERIOUS
INJURY FROM ACCIDENTAL
OPERATION:
Turn the Power Switch (15) of the tool off
and unplug the tool from its electrical
outlet before assembling or making any
adjustments to the tool.
Note: For additional information regarding the parts
listed in the following pages, refer to the Assembly
Diagram near the end of this manual.
Set-Up
Your Rotary Tool will require some set-up prior to operation.
To assist you with set-up, please refer to the following
instructions. Also see the Parts List and Assembly Diagrams
near the end of this manual.
It is important that you read the entire manual to become
familiar with the unit BEFORE you use the Rotary Tool.
Before setting-up your Rotary Tool, be sure that you have
all parts described in the Parts List.
Assemble attachments based on the intended use of
the tool.
Set-up and disassemble your Rotary Tool Set for each use.
Put back all pieces in the case provided and store in the
case to ensure that no pieces are lost.
To Insert Accessories:
1. Insert Collet (2) into the shaft. Slide the Collet Nut
(1) over the Collet. Insert the desired accessory
fully into the Collet.
2. Press down on the Lock Button (4) while turning
the Collet Nut. The shaft will click into place.
3. With the Shaft locked in place, use the Wrench
(Accessory I) to tighten the Collet Nut.
Note: Some cutting wheels, polishing tips and
accessories need to be attached or inserted into
another shaft or mandrel to be used. In these
cases, please note the following instructions.
4. Thread the accessory onto the screw of the
Mandrel (Accessory L) into the Collet. Following
the preceding steps, tighten the Collet Nut.
To Remove Accessories:
1. Press down on the Lock Button while turning the
Collet Nut counterclockwise. You will feel the Shaft
click into place.
2. With the Shaft locked in place, use the Wrench to
loosen the Collet Nut and remove the accessory.
Work Piece & Work Area Set-Up
1. Designate a work area that is clean and well-lit.
The work area must not allow access by children or
pets to prevent distraction and injury.
2. Route the power cord along a safe route to reach
the work area without creating a tripping hazard or
exposing the power cord to possible damage. The
power cord must reach the work area with enough
extra length to allow free movement while working.
3. Secure loose work pieces using a vise or clamps
(not included) to prevent movement while working.
4. There must not be hazardous objects, such as
utility lines or foreign objects, nearby that will
present a hazard while working.
5. You must use personal safety equipment including,
but not limited to, ANSI-approved eye and hearing
protection, as well as heavy work gloves and
work apron.
6. Before beginning work, plan and provide for
sparks and debris that will y off the work surface.
CAUTION: Always have access to a type AAA re
extinguisher.
Operating Instructions
TO PREVENT
SERIOUS INJURY:
Grip the tool rmly.
To assist you with operation, please refer to the
Assembly Diagram and Parts List near the end of
the manual.
Never force the tool or attachment to do the work of
a larger industrial tool. It is designed to do the job
better and more safely at the rate for which it was
intended.
1. For most uses, it is helpful to grasp the tool much
like a pencil. This will allow the nest control of
the tool. Before starting on your actual workpiece,
practice a similar action (drilling, cutting, polishing)
on a scrap piece.
2. Apply only slight pressure. Let the tool do the
work. To prevent heat build-up, do not cover the air
vents with your hands during use.