Filter
Top Products
3
Store idle tools out of reach of children
and other untrained persons.
Tools are
dangerous in the hands of untrained users.
Maintain tools with care. Keep cutting
tools sharp and clean.
Properly main-
tained tools, with sharp cutting edges are
less likely to bind and are easier to control.
Any alteration or modification is a misuse
and may result in a dangerous condition.
Check for misalignment or binding of
moving parts, breakage of parts, and any
other condition that may affect the tools
operation. If damaged, have the tool
serviced before using.
Many accidents
are caused by poorly maintained tools.
Develop a periodic maintenance schedule
for your tool.
Use only accessories that are recom-
mended by the manufacturer for your
model.
Accessories that may be suitable for
one tool, may become hazardous when
used on another tool.
Service
T
ool service must be performed only by
qualified repair personnel.
Service or
maintenance performed by unqualified per-
sonnel could result in a risk of injury. For
example: internal wires may be misplaced
or pinched, safety guard return springs may
be improperly mounted.
When servicing a tool, use only identical
replacement parts. Follow instructions in
the Maintenance section of this manual.
Use of unauthorized parts or failure to follow
Maintenance Instructions may create a risk
of electric shock or injury. Certain cleaning
agents such as gasoline, carbon tetrachlo-
ride, ammonia, etc. may damage plastic
parts.
Safety Rules for Drill Press
Unplug tool before setting up in table,
making adjustments or changing bits.
Accidental start-up of the tool can cause
injury.
Securely fasten table to a stable platform
or workbench
. During operation unstable
platforms or workbenches may shift or tip
causing loss of control and injury.
Securely fasten tool to table before oper-
ating.
If tool loosens during operation it will
tend to walk down from clamp and tool may
fall while bit is still spinning.
Know how to shut off the tool! Position the
tool so that switch is readily accessible to
quickly shut off in an emergency.
Route the cord away from the bit or cut-
ting area.
Cutting into live electrical wires
may result in a shock, burn or electrocution.
Wear eye protection and dust mask. Use
only in well-ventilated area. Using personal
safety devices and working in safe environ-
ment reduces risk of injury.
Do not wear gloves, necktie or loose
clothing during operation of the tool.
Tie
back long hair or use a hair net. Clothing or
hair can become caught in the spinning bit
and injury may occur.
Match the appropriate bit and its speed to
your application. Do not use bits that
have a cutting diameter that exceed the
capacity of the tool.
The drill press stand is
intended primarily for light duty use on wood.
Overloading the tool can lead to personal
injury or tool failure.
Never use dull or damaged bits. Sharp
bits must be handled with care.
Damaged
bits can snap during use. Dull bits require
more force to push the workpiece, possibly
causing the bit to break.
Always make sure the workpiece is free
from nails and other foreign objects.
Cutting into a nail will damage the bit and can
cause the workpiece to jump causing loss of
control.
Before operation clamp workpiece or
brace against column. Never hold a small
workpiece in one hand and bring the drill
down.
Clamping the workpiece allows you
to use both hands to control the tool.
Securing workpiece will prevent spinning or
climbing on the drill during operation.
Use a “V” block for supporting round
stock such as tubes or rods when drilling.
Round material such as dowel rods, pipes or
tubing have a tendency to roll while being
cut, and may cause the bit to "bite" or the
workpiece to jump toward you.
You must set and lock tool head into the
desired position and depth of cut when
performing operations other than drilling.
Bring the workpiece to the tool and allow
for sufficient space, at least 150 mm (6"),
between your hand and the spinning bit.
Contact with the spinning bit will cause injury.
DM 2610921728 8-05E 8/23/05 9:15 AM Page 3