Filter
Top Products
18
ENGLISH
Setting device for saw blade tilt
With the blade tilt lever (18) the saw
blade is steplessly tilted from 0° through
45°.
In order for the blade angle not to
change during cutting, the blade is
locked in position with the turning knob
(19).
Handwheel for setting the depth of
cut
The depth of cut can be adjusted by
turning the handwheel (20).
Fence
The saw is equipped with two fences:
• Mitre fence (for cross/mitre cuts):
For use as mitre fence the short
fence extrusion (21) must be
installed. The mitre fence is
mounted on a guide bar, fastened to
the left-hand side of the saw table.
The plastic nose of the fence extru-
sion must point towards the saw
blade.
For mitre cuts, the fence extrusion is
adjustable to 45° maximum.
• Rip fence (for ripping):
For use as rip fence the long fence
extrusion (22) must be installed. It is
mounted on the guide extrusion at
the front of the saw table.
After loosening the two knurled nuts
(23), the fence extrusion can be
removed and shifted:
Wide edge:
− for cutting thick stock
Small edge:
− for cutting thin stock;
− when the saw blade is tilted.
A
Danger!
Modifications of the saw or the
use of parts not tested and approved
by the equipment manufacturer can
lead to unforeseen damage during
operation!
− Assemble the saw in strict
accordance with these instruc-
tions.
− Use only the parts supplied as
standard delivery.
− Do not change any parts.
Only if you follow the instructions exactly
does the saw conform to the safety regu-
lations and can be safely operated.
If you also observe the following notes,
the assembly will cause no problems:
• Read the instructions for each step
before executing it.
• Lay out the parts required for each
assembly step.
Required tools
− Hex. wrench 4 mm
− Hex. wrench 5 mm
− Hex. wrench 6 mm
− Wrench 10 mm
− Wrench 13 mm
− Wrench 19 mm
− Ring spanner 46 mm
− Philips screwdriver
Stand assembly
1. Place table top (24) upside down on
a stable, level support. Put a layer of
cardboard or similar underneath to
prevent marring the surface.
2. Attaching the four legs (25) to the
inside of the table panel's corners:
− fit hexagon head screws (26) into
holes from the outside;
− from the inside screw on flange
nuts (27) – do not yet tighten
fully.
3. Fit long stanchions (28) between the
side legs, short stanchions (29)
between the front and rear legs:
− the wide sides of the stanchions
face the table panel;
− the nibs and recesses must fit
into each other;
− fit hexagon head screws into
holes from the outside;
− from the inside screw on flange
nuts – do not yet tighten fully.
4. Screwing up the stanchions with
each other:
− Fit hexagon head screws from
the side of the table top;
− from the other side turn on the
flange nuts – do not yet tighten
fully, this will be done after
installation of the table exten-
sion.
− With the help of another person,
turn the saw over and stand it on
a level floor.
Mounting the switch
1. Attach the switch plate with two
each hexagon head screws (30) and
flange nuts (31) to the left front leg.
The switch buttons must point to the
right-hand side.
18
19
20
21
22
6. Assembly
Item Description Qty.
24
Table top with chip case
1
25
Leg
4
26
Hexagon head screw
M8 x 16
20
27
Flange nut M8
20
28
Stanchion, long
2
29
Stanchion, short
2
23
Item Description Qty.
30
Hexagon head screw
M8 x 16
2
31
Flange nut M8
2
32
Cable tie
1
26
28
27
25
29
24