Genie 1500 Power Screwdriver User Manual


 
TABLE OF CONTENTS
Section ..............................................................Page
Safety Information 2....................................................................
Important Safety Instructions .2
Safety Features / Opener Features .3
G-1 etting Started
Overview of Powerhead Controls ............................... 4
Programming Overview ................................................... 4
Poster Review/Infrared Protection Function ...........
OPENER MUST BE INSTALLED WITH THE INCLUDED
WALL CONSOLE.
Safe-T-Beam® SAFETY REVERSE SYSTEM MUST BE
INSTALLED TO CLOSE DOOR.
SAFETY INFORMATION
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
CONVENTIONS USED IN THESE INSTRUCTIONS
Garage doors are large, heavy objects that mov
of springs under high tension and electric motors. Since moving
objects, springs under tension, and electric mot
injurie
e with the help
s, your safety and the safety of others depend on you
reading
the information in this manual. If you have questions or
ors can cause
formation presented, call your nearest
trained
door system technician or visit our website.
The following Safety Alert symbol and signal words are used
throughout this manual to call attention to and identify different
levels of hazard and special instructions.
This is the safety alert symbol. This symbol alerts you
potential hazards that can kill or hurt you and others.
to
All safety messages will follow the safety aler
and the
t symbol
word "DANGER", "WARNING", or "CAUTION"
DANGER indicates an imminently hazardous situation which,
NOT avoide
if
d, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which,
NOT avoided, could result in death or serious injury.
if
CAUTION indicates a potentially hazardous situation which,
NOT a
if
voided, may result in injury or property damage.
The word NOTE is used to indicate important steps to be
followed or important considerations.
Do NOT allow children to
play with Door Opener.
Keep people clear of opening
while door is moving.
Do NOT operate a door that
jams or has a broken spring.
OVERVIEW OF POTENTIAL HAZARDS
READ
THIS SAFETY INFORMATION
PreventionEffect
Potential
Hazard
WARNING
Could result in
Death or
Serious Injury
Could result in
Death or
Serious Injury
Could result in
Death or
Serious Injury
WARNING
WARNING
Turn OFF power before
removing opener cover.
When replacing cover, make
sure wires are NOT pinched or
near moving parts.
Opener must be fully grounded.
Do NOT try to remove, install,
repair or adjust springs or
anything to which door springs
are
fastened, such as, wood
blocks, steel brackets, cables
or other like items.
Installations, repairs and
adjustments must be done
by a trained door systems
technician using proper
tools and instruction
do not understand the in
2
©2011 The Genie Company
9/2011
P-2 rogramming
Limits and Force ...................................................................5
Optional Programming Powerhead
to HomeLink®, Car2U®, Intellicode® 1 Remotes
or Wireless Keypads
...........................................................
6
Contact Reverse Test ......................................................... 5
3-Maintenance & Troubleshooting
Monthly Routine...................................................................8
Important Safety Instructions 8........................................
Corrective Maintenance...................................................9
Adjustment Guide.............................................................10
Troubleshooting Guide............................................11-12
Warranty............................................................................... 12
REFERENCE-Wiring Diagram .........................................13
8 Safe-T-Beam® System Check...........................................
8 Door Balance (Spring Tension).......................................
8 Contact Reverse Test (Reference)..................................
9 Changing Light Bulbs ........................................................
9 Remote Battery Replacement.........................................
10 Changing Force Setting..................................................
10Changing Speed Setting ................................................
9 Belt Tensioning Adjustment ...........................................
9Travel Limit Reset ...............................................................
9Engage & Disengage Carriage........................................
Programming Intellicode® 2 Remote
to Powerhead
........................................................................ 6
........................................................6
........................... 3
Transmitter Compliance Statement
....................................................7
Lost or Stolen Remote
....................................................6
FCC and IC Certification
....................................................7
Wall Console Overview
Programming New Remotes to
Previously Installed Genie® Intellicode® 1
Garage Door Openers
.........................................
................................
4