Filter
Top Products
Power tool use and care
• Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it
was designed.
• Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and must
be repaired.
• Disconnect the plug from the power source
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting
the power tool accidentally.
• Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
• Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from intended could result
in a hazardous situation.
Service
• Have your power tool serviced by a qualified
repair personnel using only identical replacement
parts.
• When operating a power tool outdoors, use an
outdoor extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock. This will ensure that the
safety of the power tool is maintained.
Additional safety instructions for
engravers
• Always wear eye, ear and breathing protection
• Do not apply too much pressure when engraving
WARNING. The use of an accessory or attachment,
other than those recommended in this Instruction
Manual, may present a risk of personal injury.
To use this tool properly, you must observe the safety
regulations, the assembly instructions and the operating
instructions to be found in this Manual. All persons who
use and service the machine have to be acquainted with
this Manual and must be informed about its potential
hazards. Children and infirmed people must not use this
tool. Children should be supervised at all times if they
are in the area in which the tool is being used. It is also
imperative that you observe the accident prevention
regulations in force in your area. The same applies for
general rules of occupational health and safety.
The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from such
changes.
Even when the tool is used as prescribed it is not
possible to eliminate all residual risk factors. The
following hazards may arise in connection with the tool’s
construction and design:
• Damage to the lungs if an effective dust mask is
not worn.
• Damage to hearing if effective earmuffs are not worn.
• Damage to eyes if effective goggles are not worn
• Risk of injury unless hands are kept well clear of
cutting devices
Unpacking
Due to modern mass production techniques, it is unlikely
that your GMC Power Tool is faulty or that a part is
missing. If you find anything wrong, do not operate the
tool until the parts have been replaced or the fault has
been rectified. Failure to do so could result in serious
personal injury.
Installing an engraver tip
WARNING. Disconnect the engraver from the power
supply before making any adjustments or maintenance
procedures.
1. Loosen the tip release screw (4) by turning it anti-
clockwise with a flat head screwdriver.
2. To fit the new engraving tip (2), insert the tip through
the centre of the hole of the engraver, ensuring the
tip fully enters the housing. A new tip should protrude
from the end of the housing by approximately 8.5mm.
3. Tighten the tip release screw (4) fully by rotating in a
clockwise direction.
Operation
WARNING. Always wear safety glasses when using
this tool.
The GMC engraver can be used to permanently mark
metal, glass, plastic, wood, ceramics and much more.
1. Before using the engraver you must ensure there is
an engraving tip installed.
2. Connect the engraver plug to the power supply and
while holding the engraver firmly, push up on the
on/off switch (1) with your thumb.
NOTE. To turn the tool on, press the small On/Off
Switch (1) upwards to the (I) position. To turn the tool off,
push the on/off Switch (1) down to the (O) position.
3. Hold the engraver at an angle, like you would hold a
pen. Do not press down hard while engraving, use
light pressure while guiding the point over the work to
be completed.
Adjusting the depth of engraving
1. The stroke adjustment dial (3) located on the side of
the engraver controls the stroke length and therefore
the depth of engraving.
2. For a fine mark turn the stroke adjustment dial (3)
anti-clockwise to position ‘1’.
3. For a deeper, thicker mark turn the stroke adjustment
dial (3) clockwise to position ‘5’
NOTE. It is recommended that you practice on scrap
material before you start.
Maintenance
WARNING. Always ensure that the tool is switched
off and the plug is removed from the power point before
making any adjustments or maintenance procedures.
1. Use a soft brush to remove any accumulated dust.
Wear safety glasses to protect your eyes whilst
cleaning.
2. If the body of the tool needs cleaning, wipe it with a
soft damp cloth. A mild detergent can be used but
never alcohol, petrol or other harsh cleaning agents.
3. Never use caustic agents to clean plastic parts.
CAUTION. Water must never come into contact with
the tool.
General inspection
Regularly check that all the fixing screws are tight. They
may vibrate loose over time.
Power cord maintenance
If the supply cord needs replacing, the task must be
carried out by the manufacturer, the manufacturer’s
agent, or an authorised service centre in order to avoid
a safety hazard.
Please refer to your warranty card, which is separate to
these instructions.
45–55 South Centre Road Melbourne Airport
Victoria, Australia 3045
Tel: (03) 8346 1100 Fax: (03) 8346 1200
Full 2-Year Warranty
This product is warranted for a 2-year period for
home domestic use from the date of the original
purchase. If found to be defective in materials
or workmanship, the tool or the offending faulty
component will be replaced free of charge with
another of the same item. A small freight charge
may apply.
The warranty replacement unit is only made
available by returning the tool to the place of
purchase with a confirmed register receipt.
Proof of purchase is essential. We reserve the
right to reject any claim where the purchase
cannot be verified. This warranty does not
include damage or defects to the tool caused by
or resulting from abuse, accidents, alterations or
commercial or business use.
Consistent with our product development
programme, improvements may have been made
which render the contents of the tool’s packaging
or user instructions slightly different to the
product received.
Phone (03) 8346 1100 Facsimile (03) 8346 1200
Email info@gmca.com.au
Website www.gmcompany.com
Copyright Global Machinery Company Australia
Proprietary Limited, 2001
Dear customer, if you require any help with your
product, whether it is a Warranty Claim, spare
part or user information, please phone our
Help Line
1300 880 001 (Australia)
or 0800 445 721 (New Zealand), for an
immediate response.
Product of China manufactured to exacting
GMC quality standards.
ABN: 68 093 174 808
The GMC 777 Helpline
operates from 7am to
7pm, 7 days a week (EST).
This allows you to contact GMC directly with
any queries and technical questions you have
regarding our products.
Save this Manual for future reference.