Filter
Top Products
Technical Data
312667K 49
Technical Data
MAGNUM X5
(Series A - C)
MAGNUM X5
(Series D)
MAGNUM X7
(SeriesC)
Working pressure range 0-2800 psi
(0-19 MPa,
0-193 bar)
0-3000 psi
(0-21 MPa,
0-207 bar)
0-3000 psi
(0-21 MPa,
0-207 bar)
Electric motor
9.0A
(open frame, universal)
9.0A
(open frame, universal)
9.0A
(open frame, universal)
Operating horsepower 1/2 1/2 5/8
Maximum delivery (with tip) 0.24 gpm (0.91 lpm) 0.27 gpm (1.02 lpm) 0.31 gpm (1.17 lpm)
Paint hose 1/4 in. x 25 ft
(6.4 mm x 7.5 m)
1/4 in. x 25 ft
(6.4 mm x 7.5 m)
1/4 in. x 25 ft
(6.4 mm x 7.5 m)
Maximum tip hole size
0.015 in. (0.38 mm) 0.015 in. (0.38 mm) 0.017 in. (0.43 mm)
Weight, sprayer only 13.3 lb (6.0 kg) 13.3 lb (6.0 kg) 23.3 lb (10.6 kg)
Weight, sprayer, hose & gun 16.5 lb (7.5 kg) 16.5 lb (7.5 kg) 26.5 lb (12.0 kg)
Dimensions (Upright):
Length 14.5 in. (36.8 cm) 14.5 in. (36.8 cm) 19.3 in. (49.0 cm)
Width 12.4 in. (31.5 cm) 12.4 in. (31.5 cm) 15.3 in. (38.9 cm)
Height 17.9 in. (45.5 cm) 17.9 in. (45.5 cm) 37.0 in. (94.0 cm)
Dimensions (Folded):
Length N/A N/A 19.3 in. (49.0 cm)
Width N/A N/A 15.3 in. (38.9 cm)
Height N/A N/A 29.2 in. (74.2 cm)
Power cord 18 AWG, 3-wire, 6 ft (1.8 m)
Fluid inlet fitting 3/4 in. internal thread (standard garden hose thread)
Fluid outlet fitting 1/4 NPSM external thread
Inlet screen (on suction tube) 35 mesh (450 micron)
Wetted parts, pump & hose stainless steel, brass, leather, ultra-high molecular weight polyethylene
(UHMWPE), carbide, nylon, aluminum, PVC, polypropylene,
fluroelastomer
Wetted parts, gun aluminum, brass, carbide, nylon, plated steel, stainless steel,
UHMWPE, zinc
Generator requirement 1500 Watt minimum
Electrical power requirement 120 Vac, 60 Hz, 15A, 1 phase
Storage temperature range ◆❖ -30° to 160°F (-35° to 71°C)
Operating temperature range ✔ 40° to 115°F (4° to 46°C)
◆ When pump is stored with non-freezing fluid. Pump damage will occur if water or latex paint freezes in pump.
❖ Damage to plastic parts may result if impact occurs in low temperature conditions.
✔ Changes in paint viscosity at very low or very high temperatures can affect sprayer performance.