Grizzly G0514X3 Saw User Manual


  Open as PDF
of 92
 
"()"
<%*&)M"M(B[\#&%$%* !<%*&)M'B[\#)$%, 
Aligning Table
IdZchjgZXjii^c\VXXjgVXnl]Zci]ZiVWaZ^h[^ghi
^chiVaaZY!i]ZiVWaZh]djaYWZVa^\cZYhdi]Vii]Z
b^iZghadi^h eVgVaaZaidi]Z WVcYhVlWaVYZ#I]^h
egdXZYjgZldg`hWZhil^i]V
(
¿)WaVYZ^chiVaaZY#
To align the table so the miter slot is parallel
to the bandsaw blade:
1. BV`ZhjgZi]Vii]ZWaVYZ^higVX`^c\egdeZgan
VcYi]Vi^i^hXdggZXianiZch^dcZY#
2. 9>H8DCC:8I76C9H6L;GDBEDL:G
3. AddhZc i]Z igjcc^dc Wdaih i]Vi hZXjgZ i]Z
igjcc^dchidi]ZiVWaZ#
4. EaVXZ Vc VXXjgViZ higV^\]iZY\Z Vadc\ i]Z
WaVYZ#I]ZhigV^\]iZY\Zh]djaYa^\]ianidjX]
Wdi]i]Z[gdciVcY WVX`d[i]ZWaVYZ#Note:
Make sure the straightedge does not go
across a tooth.
5. JhZV[^cZgjaZgid\Vj\Zi]ZY^hiVcXZ
WZilZZci]ZhigV^\]iZY\ZVcYi]Zb^iZghadi#
I]ZY^hiVcXZndjbZVhjgZh]djaYWZi]Z
hVbZViWdi]i]Z[gdciVcYi]ZWVX`d[i]Z
iVWaZhZZFigure 47#
6. 6Y_jhii]ZiVWaZVhcZZYZY[dgegdeZgVa^\c"
bZci#
7. I^\]iZci]Zigjcc^dcWdaih#
Figure 47. BZVhjg^c\[dgb^iZghadiidWZeVgVaaZa
l^i]WaVYZ#
IdZchjgZXjii^c\VXXjgVXnl]Zci]Z[ZcXZ^h[^ghi
^chiVaaZY! i]Z [ZcXZ h]djaY WZ Va^\cZY l^i] i]Z
b^iZghadi#
To align the fence parallel with the miter slot:
1. >[i]Z[ZcXZ^hbdjciZYdci]ZaZ[i"]VcYh^YZ
d[i]ZWaVYZ!gZbdkZ^iVcYgZbdjci^icZmiid
i]Zb^iZghadi#
2. AddhZci]Z[djg XVehXgZlhadXViZYdc i]Z
ide[VXZd[i]Z[ZcXZFigure 48#
Aligning Fence
Figure 48.;djg[ZcXZXVehXgZlh#
3. 6Y_jhii]Z[ZcXZ[VXZeVgVaaZal^i]i]ZZY\Zd[
i]Zb^iZghadi#
4. I^\]iZci]Z[djgXVehXgZlh!WZ^c\XVgZ[jacdi
idbdkZi]Z[ZcXZ#
NOTICE
Adjusting the fence parallel to the miter slot
does not guarantee straight cuts. The miter
slot may need to be adjusted parallel to the
side of the blade. Refer to the "Aligning
Table" instructions.
 previous next