Grizzly G0555LX Saw User Manual


  Open as PDF
of 68
 
"')"
<%***AMB[\#H^cXZ%&$&'
I]Z YZ[aZXi^dc bZi]dY ^h bjX] bdgZ hjW_ZXi^kZ
i]Vc i]Z [ajiiZg bZi]dY# :VX] WaVYZ l^aa YZ[aZXi
Y^[[ZgZcian VcY ZkZgn jhZg l^aa YZiZgb^cZ l]Vi
bdYZgViZ egZhhjgZ bZVch# I]Z [daadl^c\ VgZ
\ZcZgVa \j^YZa^cZh [dg iZch^dc^c\ i]Z WaVYZ l^i]
i]^hbZi]dY#
To tension the bandsaw blade:
1. 9>H8DCC:8I76C9H6L;GDBEDL:G#
2. BV`Z hjgZi]Z WaVYZ^h egdeZgan igVX`^c\Vh
^chigjXiZY^ci]ZBlade Tracking hjWhZXi^dc
dc Page 19#
3. GV^hZ i]Z \j^YZ edhi Vaa i]Z lVn VcY bdkZ
i]Z jeeZg VcY adlZg \j^YZ WZVg^c\h VlVn
[gdbi]ZWaVYZ#
4. :c\V\Zi]ZWaVYZiZch^dcfj^X`gZaZVhZaZkZg
idVeeaniZch^dcidi]ZWaVYZ#
5. Jh^c\bdYZgViZegZhhjgZ!ejh]i]ZXZciZgd[
i]ZWaVYZh^YZlVnh#
·>[i]ZWaVYZYZ[aZXihVeegdm^bViZan
&
¿)^i^h
egdeZganiZch^dcZY#EgdXZZYidStep 7#
·>[i]ZWaVYZYZ[aZXihaZhhi]Vc
&
¿)^i^hdkZg"
iZch^dcZY#Ijgci]ZWaVYZiZch^dc^c\`cdW
XdjciZgXadX`l^hZild[jaaijgchVcYgZeZVi
Step 6#
·>[i]ZWaVYZYZ[aZXih
&
¿)dgbdgZ!i]ZWaVYZ
^hcdiegdeZganiZch^dcZY#6eeaniZch^dcid
i]ZWaVYZ^cXgZbZciVaanVcYgZeZViStep 6
jci^aegdeZganiZch^dcZY#
6. GZ"VY_jhi WaVYZ \j^YZh Vh YZhXg^WZY ^c
Adjusting Blade Support Bearings VcY
Adjusting Blade Guide Bearingsdc Pages
25– 26#
When using different size blades, the blade
tensioning system may need to be reset for
correct operation. Refer to Blade Tensioner
on Page 52 for detailed instructions.
Note: Tensioning the blade according to the
blade tension scale before the Test Run was an
approximate tension. The following procedures
fine-tunes the blade tension.
1. 9>H8DCC:8I76C9H6L;GDBEDL:G#
2. BV`ZhjgZi]ZWaVYZ^hegdeZganXZciZgigVX`"
^c\Vh^chigjXiZY^ci]ZBlade Tracking hjW"
hZXi^dcegZk^djhdc Page 19#
3. GV^hZ i]Z \j^YZ edhi Vaa i]Z lVn VcY bdkZ
i]Z jeeZg VcY adlZg \j^YZ WZVg^c\h VlVn
[gdbi]ZWaVYZ#
4. :c\V\Zi]ZWaVYZiZch^dcfj^X`gZaZVhZaZkZg
idVeeaniZch^dcidi]ZWaVYZ#
10. GZ"VY_jhi WaVYZ \j^YZh Vh YZhXg^WZY ^c
Adjusting Blade Support Bearings VcY
Adjusting Blade Guide Bearingsdc
Pages 25– 26#
9. 9^hXdccZXii]ZWVcYhVl[gdbedlZg#
5. 8dccZXii]ZWVcYhVlidedlZg!VcYijgci]Z
WVcYhVlON#
6 . Jh^c\ i]Z WaVYZ iZch^dc VY_jhibZci `cdW!
hadlanYZXgZVhZ WaVYZiZch^dc jci^andj hZZ
i]ZWaVYZhiVgiid[ajiiZg#
7# Hadlan ^cXgZVhZ i]Z iZch^dc jci^a i]Z WaVYZ
hideh[ajiiZg^c\!i]Zci^\]iZci]ZWaVYZiZch^dc
VY_jhibZci`cdWVcY VYY^i^dcVa
&
¿-id
&
¿)d[V
ijgc#
8. Add` Vi l]Vi i]Z iZch^dc \Vj\Z gZVYh VcY
jhZi]ViVhV\j^YZ[dgiZch^dc^c\i]ViheZX^[^X
WaVYZ^ci]Z[jijgZ#
Note: Do not rely on this setting for other
blades or for long periods of time because all
blades require specific tensioning and stretch
with use. If you notice a decrease in perfor-
mance at the setting repeat this procedure.
With extended use, the blade tensioning sys-
tem may need to be reset. Refer to Resetting
Blade Tensioner in the Service section in
this manual for details.
The Flutter Method
The Deflection Method
 previous next