Grizzly G0569 Cordless Saw User Manual


  Open as PDF
of 76
 
"('"
BdYZa<%*+-$<%*+.B[\#&%$%) 
To adjust the lower blade guides:
1. BV`ZhjgZi]ZWaVYZ^higVX`^c\egdeZganVcY
i]Vi^i^hXdggZXianiZch^dcZY#
2. 9>H8DCC:8I76C9H6L;GDBEDL:G
3. ;Vb^a^Vg^oZndjghZa[l^i]i]ZWaVYZ\j^YZXdc"
igdahh]dlc^cFigure 39#
Adjusting Support
Bearings
I]Z hjeedgi WZVg^c\h VgZ edh^i^dcZY WZ]^cY
i]Z WaVYZ [dg hjeedgi Yjg^c\ Xjii^c\ deZgVi^dch#
EgdeZgVY_jhibZcid[i]Z hjeedgiWZVg^c\h ^hVc
^bedgiVcieVgid[bV`^c\VXXjgViZXjihVcY Vahd
`ZZehi]ZWaVYZiZZi][gdbXdb^c\^cXdciVXil^i]
i]Z\j^YZWZVg^c\hl]^aZXjii^c\#
To adjust the upper support bearing:
1. BV`ZhjgZi]ZWaVYZ^higVX`^c\egdeZganVcY
i]Vi^i^hXdggZXianiZch^dcZY#
2. 9>H8DCC:8I76C9H6L;GDBEDL:G
3. ;Vb^a^Vg^oZ ndjghZa[ l^i] i]Z jeeZg hjeedgi
WZVg^c\Xdcigdahh]dlc^cFigure 36 & 37#
NOTICE
Whenever changing a blade or adjusting ten-
sion and tracking, the upper and lower blade
support bearings and blade guide bearings
must be properly adjusted before cutting
operations.
7VcYhVl
7aVYZ
Hjeedgi
7ZVg^c\
IdeK^Zl
Figure 41.>aajhigVi^dcd[WaVYZhZieZgeZcY^XjaVg
.%ßidi]ZhjeedgiWZVg^c\[VXZ#
4. AddhZci]Z\j^YZWadX`VhhZbWanhXgZlVcY
gdiViZ i]Z WaVYZ \j^YZ VhhZbWan h^YZ"id"
h^YZ!jci^ai]ZWaVYZ^heZgeZcY^XjaVgl^i]i]Z
[VXZd[i]ZhjeedgiWZVg^c\!Vh^aajhigViZY^c
Figure 41#
Hjeedgi7ZVg^c\
7aVYZ
Figure 39#AdlZgWaVYZ\j^YZXdcigdah[gdci
k^Zl#
@cjgaZY
@cdW
7aVYZ<j^YZ7ZVg^c\h
Figure 40. AdlZgWaVYZ\j^YZXdcigdahgZVg
k^Zl#
4. ;daadli]ZegdXZYjgZ[dgVY_jhi^c\i]ZjeeZg
WaVYZ\j^YZhdcPage 30#
Note:The lateral adjustment rod screw and
guide block assembly screws are located
below the table tilt lock lever (see Figure
40.
AViZgVa
6Y_jhibZci
GdYHXgZl
7ZVg^c\GdiVi^dc
6Y_jhibZci7dai
<j^YZ7adX`6hhZbWanHXgZlh
 previous next