Grizzly G0621X Saw User Manual


  Open as PDF
of 60
 
BdYZa<%+'&MB[\#-$%. 
"'("
NOTICE
Whenever changing a blade or adjusting
tension and tracking, the upper and lower
blade guides and guide-blocks must be re-
adjusted before cutting operations.
NOTICE
The blade guides should not touch the blade
after the dollar bill is removed.
Figure 27.HfjVg^c\iVWaZidWaVYZ#
6. HZXjgZi]ZeaVhi^X`cdWhVcYadX`i]Zedh^i^kZ
hideWdaiWni^\]iZc^c\i]Z]ZmcjiV\V^chii]Z
XVhi^c\#Ensure that the bolt does not turn by
holding it with another wrench while tighten-
ing the hex nut.
6c VY_jhiVWaZ edh^i^kZ hide Vaadlh i]Z iVWaZ id
ZVh^angZijgcid.%ßV[iZgi^ai^c\#
To set the positive stop 90˚ to the blade:
1. BV`ZhjgZi]ZWaVYZ^hXdggZXianiZch^dcZYVh
YZhXg^WZY^c i]ZTensioning Blade ^chigjX"
i^dchdcPage 20#
2. 9>H8DCC:8I76C9H6L;GDBEDL:G
3. AddhZci]ZildeaVhi^X`cdWhi]VihZXjgZi]Z
iVWaZidi]Zigjcc^dch#
4. AddhZc i]Z ]Zm cji i]Vi adX`h i]Z edh^i^kZ
hideWdai^ceaVXZ#
5. GV^hZ i]ZjeeZg WaVYZ\j^YZ VhhZbWan VcY
eaVXZ V +bVX]^c^hi»h hfjVgZ dgign"hfjVgZ
dci]ZiVWaZcZmiidi]Zh^YZd[i]ZWaVYZVh
^aajhigViZY ^c Figure 27# 6Y_jhi i]Z edh^i^kZ
hideWdaiidgV^hZdgadlZgi]ZiVWaZjci^ai]Z
iVWaZ^h.%ßidi]ZWaVYZ#
Adjusting Positive
Stop
I]Zed^ciZgdci]ZiVWaZi^aihXVaZbjhiWZXVa^"
WgViZY^cdgYZg[dgi]ZhXVaZgZVY^c\idWZVXXj"
gViZ#
To calibrate the pointer on the table tilt scale:
1. BV`Z hjgZ i]Z WaVYZ ^h iZch^dcZY$igVX`^c\
XdggZXianVcYi]Vii]ZiVWaZ^h.%ßidi]ZWaVYZ
i]^hegdXZYjgZh]djaYWZVagZVYnXdbeaZiZY
l^i] i]Z Adjusting Positive Stop ^chigjX"
i^dch#
2. AddhZci]Zed^ciZghXgZl#
3. 6a^\ci]Zi^ed[i]Zed^ciZgl^i]i]Z%ßbVg`dc
i]ZiVWaZi^aihXVaZ#
4. I^\]iZci]Zed^ciZghXgZl#
Setting Table
Tilt Scale to 0˚
 previous next