Grizzly G0709 Lathe User Manual


  Open as PDF
of 112
 
BdYZa<%,%.B[\#H^cXZ*$&&
"(("
Use a minimum of three independent clamp-
ing devices when using faceplate. Failure
to provide adequate clamping may cause
workpiece to eject during operation.
Figure 31.Ldg`e^ZXZegdeZganXaVbeZYdci]Z
[VXZeaViZ^cVb^c^bjbd[i]gZZadXVi^dch
iV^ahidX`gZbdkZY[dgXaVg^in#
6. 9djWaZ X]ZX` [dg hV[Zin VcY gdiVi^dc XaZVg"
VcXZ#
7. Ha^YZ i]Z iV^ahidX` VlVn [gdb i]Z ldg`e^ZXZ
VcY ^chiVaa i]Z gZfj^gZY iV^ahidX` idda^c\ [dg
Yg^aa^c\ dg Wdg^c\! dg edh^i^dc i]Z idda W^i [dg
[VX^c\#
Centers
I]ZBdYZa<%,%.aVi]Z^hhjeea^ZYl^i]ildBI(
YZVYXZciZgh!VcBI(a^kZXZciZg!VcYVBI*¶
BI(VYVeiZghaZZkZhZZFigure 32idVYVeii]Z
XZciZgh^cidhe^cYaZWdgZ#L]Zc^chiVaa^c\XZciZgh
kZg^[ni]ViVaabVi^c\hjg[VXZhVgZXaZVcVcY[gZZ
d[c^X`hVcYWjggh#
Tip: Hand-held tapered bore wipers make this
task very time efficient, and offer consistently
clean bores.
To use the faceplate:
1. 9>H8DCC:8IA6I=:;GDBEDL:G
2. >chZgi V YZVY XZciZg ^cid i]Z iV^ahidX`! ha^YZ
i]ZiV^ahidX`jeidi]Z[VXZeaViZ!VcYadX`i]Z
iV^ahidX`^cidedh^i^dc#
3. EaVXZ i]Z ldg`e^ZXZ V\V^chi i]Z [VXZeaViZ
VcYijgci]ZiV^ahidX`fj^aahdi]Zed^cid[i]Z
YZVY XZciZg idjX]Zh VcY Veea^Zh Zcdj\]
egZhhjgZid]daYi]Zldg`e^ZXZ^ceaVXZ#
4. AdX` i]Z fj^aa l]Zc hj[[^X^Zci egZhhjgZ ^h
Veea^ZY id ]daY i]Z ldg`e^ZXZ# 6YY^i^dcVa
hjeedgi bVn WZ cZZYZY! YZeZcY^c\ dc i]Z
ldg`e^ZXZ#
5. 8aVbei]Zldg`e^ZXZViVb^c^bjbd[i]gZZ
adXVi^dch i]Vi VgZ Vh XadhZ id WZ^c\ ZkZcan
heVXZYVeVgiVhedhh^WaZVhh]dlc^cFigure
31.
Solid Dead Center
9ZVYXZciZghVgZine^XVaanjhZY^cadlheZZYijgc"
^c\deZgVi^dchid^cXgZVhZg^\^Y^in[dgXadhZidaZg"
VcXZh# I]Z hda^Y YZVY XZciZg ^h ^chiVaaZY Vi i]Z
he^cYaZZcYd[i]Z aVi]Z WZXVjhZi]Zldg`e^ZXZ!
XZciZg!VcYhe^cYaZVaaijgcid\Zi]ZgWni]ZjhZd[
VaVi]ZYd\#DcZZcYd[i]ZaVi]ZYd\^hXaVbeZY
id i]Z ldg`e^ZXZ! VcY i]Z di]Zg ZcY i]Z iV^a! ^h
^chZgiZY ^cid V [VXZeaViZ hadi h]dlc ^c Figure
33#
Tip:If the tail is too large for a slot, install the
3-jaw chuck, open the jaws so the workpiece can
be supported by the center and the tail of the dog
can rest against a jaw.
Figure 32. >cXajYZYXZciZghVcYhaZZkZ#
A^kZ8ZciZg8VgW^YZ"I^eeZY9ZVY8ZciZg
Hda^Y9ZVY8ZciZg
HaZZkZ
Figure 33.;VXZeaViZVcYYZVYXZciZghZije#
;VXZeaViZHadi
Hda^Y9ZVY8ZciZg
 previous next