Grizzly G1023RLW Saw User Manual


  Open as PDF
of 96
 
BdYZa<&%'(GAHZg^ZhB[\#H^cXZ,$&%
")&"
6g^ee^c\WaVYZ^hine^XVaani]ZWZhiWaVYZidjhZ
[dgXjii^c\gVWWZihl]Zc jh^c\VhiVcYVgYWaVYZ
WZXVjhZ^igZbdkZhhVlYjhikZgnZ[[^X^Zcian#HZZ
Page 29[dgWaVYZYZiV^ah#6ahd!VhVXg^[^X^Va[ZcXZ
^hcdigZfj^gZYl]ZcXjii^c\gVWWZihl^i]VhiVc"
YVgYWaVYZ#
To cut rabbets with the standard blade:
1. 9>H8DCC:8IH6L;GDBEDL:G
2. :chjgZ i]Vi i]Z g^k^c\ `c^[Z VcY hiVcYVgY
iVWaZ^chZgiVgZ^chiVaaZY#Dg^chiVaai]Zdei^dc"
VaBdYZa=)'(&oZgdXaZVgVcXZ^chZgi!bV`"
^c\hjgZi]ZXZciZghZXi^dcd[i]Z^chZgi]Vh
VagZVYnWZZcgZbdkZY·hdi]ZWaVYZXVcWZ
gV^hZYXdggZXian^ci]Z[daadl^c\hiZeh#
3. BVg`i]Zl^Yi]d[i]ZgVWWZiXjidci]ZZY\Z
d[i]Zldg`e^ZXZ!hdndjXVcXaZVgan^YZci^[n
i]Z^ciZcYZYXjil]^aZ^i^haVn^c\[aVidci]Z
hVliVWaZ#
4. GV^hZi]ZWaVYZjeidi]ZYZh^gZYYZei]d[Xji
YZei]d[gVWWZiX]VccZaYZh^gZY#
5. HiVcYi]Z ldg`e^ZXZ dc ZY\Z! Vh h]dlc ^c
Figure 61, i]ZcVY_jhii]Z[ZcXZhdi]ZWaVYZ
^hVa^\cZYl^i]i]Z^ch^YZd[ndjggVWWZiX]Vc"
cZa#
Cutting Rabbets with a Standard
Blade
;ZcXZ
Blade
Ldg`e^ZXZ
Figure 61. GVWWZiXjii^c\l^i]VhiVcYVgYWaVYZ#
·>[i]Zldg`e^ZXZ^hkZgniVaa, VcY^hjchiVWaZ
l]ZceaVXZYV\V^chii]Z[ZcXZ!aVn^i[aVidc
i]ZiVWaZVcYjhZVYVYdWaVYZideZg[dgb
i]ZgVWWZiXji#
Ldg`e^ZXZ
;ZcXZ
Blade
Figure 62. HZXdcYXjiidXgZViZVgVWWZi#
6. GZXdccZXii]ZhVlidi]ZedlZghdjgXZ!i]Zc
eZg[dgbi]ZXji#
7. AVni]Zldg`e^ZXZ[aVidci]ZiVWaZ!Vhh]dlc
^cFigure 62!VY_jhii]ZhVlWaVYZ]Z^\]iid
^ciZghZXi l^i] i]Z [^ghi Xji! i]Zc eZg[dgb i]Z
hZXdcYXjiidXdbeaZiZi]ZgVWWZi#
DO NOT place a tall board on edge to per-
form a rabbet cut with a standard blade.
Workpieces that are too tall to properly sup-
port with the fence can easily shift during
operation and cause kickback. Instead, place
the stock flat on the saw and perform the
rabbet cut with a dado blade, as instructed
on Page 40.
15
30
45
 previous next