Grizzly G4003G Lathe User Manual


  Open as PDF
of 76
 
BdYZa<)%%(<B[\#H^cXZ)$%-
"*"
I]Z^c[dgbVi^dcXdciV^cZY]ZgZ^c^hYZZbZYVXXjgViZVhd[+$(%$'%&&VcYgZegZhZcihdjgbdhigZXZciegdYjXiheZX^[^XVi^dch#
9jZiddjgdc\d^c\^begdkZbZciZ[[dgih!i]^h^c[dgbVi^dcbVncdiVXXjgViZanYZhXg^WZ^iZbhegZk^djhanejgX]VhZY#
E6<:'D;(BdYZa<)%%(<
BV^cHeZX^[^XVi^dch/
DeZgVi^dc>c[d
Swing Over Bed......................................................................................................................................... 12 in.
Distance Between Centers........................................................................................................................ 36 in.
Swing Over Cross Slide............................................................................................................................... 7 in.
Swing Over Saddle.......................................................................................................................... 11-11/32 in.
Swing Over Gap........................................................................................................................................ 17 in.
Maximum Tool Bit Size............................................................................................................................. 5/8 in.
Compound Travel.................................................................................................................................. 3-1/4 in.
Carriage Travel.......................................................................................................................................... 24 in.
Cross Slide Travel................................................................................................................................. 6-1/4 in.
=ZVYhidX`>c[d
Spindle Bore........................................................................................................................................... 40 mm.
Spindle Size........................................................................................................................................... 3-1/4 in.
Spindle Taper............................................................................................................................................ MT#5
Number of Spindle Speeds............................................................................................................................... 9
Spindle Speeds................................................................. 70, 200, 220, 270, 360, 600, 800, 1000, 1400 RPM
Spindle Type.............................................................................................................................. D1-5 Cam Lock
Spindle Bearings................................................................................................ High Precision Tapered Roller
Spindle Length........................................................................................................................................... 17 in.
Spindle Length with 3-Jaw Chuck....................................................................................................... 21-3/4 in.
Spindle Length with 4-Jaw Chuck....................................................................................................... 21-1/4 in.
IV^ahidX`>c[d
Tailstock Quill Travel................................................................................................................................... 4 in.
Tailstock Taper.......................................................................................................................................... MT#3
Tailstock Barrel Diameter.................................................................................................................... 1-9/16 in.
I]gZVY^c\>c[d
Number of Longitudinal Feeds....................................................................................................................... 40
Range of Longitudinal Feeds.................................................................................................. 0.0011 - 0.031 in.
Number of Cross Feeds................................................................................................................................. 40
Range of Cross Feeds................................................................................................... 0.0004 - 0.0105 in./rev.
Number of Inch Threads................................................................................................................................. 40
Range of Inch Threads..................................................................................................................... 4 - 112 TPI
Number of Metric Threads.............................................................................................................................. 29
Range of Metric Threads................................................................................................................ 0.2 - 4.5 mm
9^bZch^dch
Bed Width.............................................................................................................................................. 7-1/4 in.
Leadscrew Diameter............................................................................................................................. 0.870 in.
Leadscrew TPI.................................................................................................................................................. 8
Leadscrew Length..................................................................................................................................... 44 in.
Steady Rest Capacity................................................................................................................. 3/16 - 1-1/2 in.
Follow Rest Capacity........................................................................................................................ 1/4 - 3/4 in.
Faceplate Size........................................................................................................................................... 10 in.
Feed Rod Diameter.............................................................................................................................. 0.780 in.
Floor to Center Height......................................................................................................................... 46-1/4 in.
8dchigjXi^dc
Base................................................................................................................................................................ in.
Headstock............................................................................................................................................ Cast Iron
Headstock Gears............................................................................................................ Flame Hardened Steel
Bed...................................................................................................................... Induction Hardened Cast Iron
Body..................................................................................................................................................... Cast Iron
Stand.................................................................................................................................................... Cast Iron
Paint......................................................................................................................................................... Epoxy
 previous next