Haier FCD-JTHMG100- E Drill User Manual


 
Before Usage
Special Reminding
To ensure proper and safe use of the water heater, we hereby sincerely declare that users
shall contact our designated professional service providers for installation and service.
For inappropriate installation, Haier would not undertake any liability.
Do disconnect the power supply before any maintenance and repair on the water heater.
Unprofessional persons shall not adjust or repair the water heater.
Make sure the machine is full of water before powering it on, otherwise heating element
may be damaged. Do ensure power socket complies with local standard and is reliably
grounded. Ungrounded use is forbidden.
This electric water heater is provided with a safety valve, which shall not be randomly
relocated or blocked.
Hot water above 50 may burn your skin. Do mix hot water and cold water before
showering or washing.
At an ambient temperature below 0 , possible ice formation within pipes may break the
pipes and cause the machine inoperable. Protection shall be made by emptying water in
the tank. In case the water heater will not be used for more than 1 month, please empty
the water and unplug the power plug.
If the electric water heater is heavily wetted by water, it should be checked by our
authorized technicians before next use.
Hot water inside the water heater is not drinkable. Due to long time use, sediments will
form inside the tank, and water quality may also deteriorate due to pipe aging. After
washing rice and vegetables with water from the tank, please flush again with clean
water.
Please do not place flammable matters like gasoline nearby the water heater, otherwise
accidents like fire may occur.
Features
1. High Technology:
Full PC controlled. Display indicates the actual water temperature, temperature setting,
clock and working state. Upon faults, power supply is automatically cut off and the
display indicates fault code.
The intelligent heating feature reflects a more humanized design.
Use of Remote Controller
1.
2.
3.
button: Power on / off the machine. In off status, clock time is displayed and can be
adjusted by pressing Set button, and or button.
Mode button: With machined powered on, you can lightly press Mode button to shift
between Real-time Heat / Warm, Medium Warm, Night Power, Time 1,Time 2,Time
1+Time 2 and Intelligent operation modes. In Medium Warm mode, default highest
temperature is 40 and can't be adjusted. In Time 1 and Time 2 modes, default heating
power is 2150W and can't be adjusted.
Ppwer button: With machine powered on, press this button to shift heating power level
between 850 W, 1300 W and 2150 W.
or button: Same as Adjust button on control panel. If not in clock or delay time
adjusting status, you can use or button to increase or decrease temperature setting
value between 35 - 75 with an increment 1 . If in clock or delay time adjusting status,
these buttons can be used to increase or decrease time.
Set button: Press it to set clock time, and press or button to adjust the value. Press
Confirm button after adjusting. In Real-time Heat / Warm mode, press Set button to
adjust clock hour and minute together with Confirm button. In Time 1 mode, press Set
button to set Time 1 hour and minute. In Time 2 mode, press Set button to set Time 2 hour
and minute. In Time 1 + Time 2 mode, press Set button to set Time 1 hour and minute,
and Time 2 hour and minute. In addition, in Medium Warm mode and Intelligent mode,
Set button is inactive.
4.
5.
Notes:
1. Remote controller buttons (except Set button) are used in the same way as buttons
with same name on control panel. After adjustment is made with Set button, press
Confirm button to confirm.
2. Remote controller has a memory function. Upon re-starting after powering off, original
settings keep unchanged.
3. As an optimum, remote controller shall be used in short distance pointing to the
machine vertically. Water immersion shall be avoided. If battery is used up, to prevent
battery liquid pollution, please open battery cover in indicated direction, remove used
batteries and replace with new batteries installed as original. To avoid explosion, used
batteries shall not be kept in hot places or put in fire, but shall be treated in accordance
with related local regulations.
Electric Circuit Diagram
Leakage Coil
Relay
Relay
Relay
ACTUAL
HEATING
KEEPING
SET
L: Brown wire
N: Blue wire
MT: High temperature limiter
EH: Heating element
RT: Sensor
E:Yellow/green wire
L
N
E
RT
E
MT
EH
Dear users,
Thanks for choosing Haier water heater product.
products have good quality and excellent performance. To facilitate you to use the
product, please read the manual and operate accordingly. Please retain it for future
reference.
The international star service of Haier Group will always accompany you. No matter
what kind of problems you meet in usage, please contact with the local after -sales service
agent. We are at your service all the time. Thanks again for choosing Product.
The water heater you purchased may not full comply with the manual due to the
improvement of product. We apologize for the inconvenience occurred therefrom.
Haier
Haier