Filter
Top Products
KEEPING
SET
HEATING
SET
HEATING
ACTUAL
KEEPING
ACTUAL
Rated voltage: 230V~ , 50Hz Dimensions: (see to Fig. 1)
Power: 850 W /1300 W / 2150 W Weight: (see to Fig. 1)
Rated pressure: 0.75 MPa Volume :(see to Fig. 1)
Waterproof grade: IPX4 ( ) Tap water pressure: not less than 0.05 MPa
Parameters
Setting Environment
²»Òª°²×°ÓÚÎÞ·¨ÅÅË®µÄµØ·½
Do not install it outdoors.
Do not install it as stand-alone.
It shall be hung on firm and solid wall.
Do not install it in places unable to drain
water.
Do not locate in freezing places. If ice
forms, tank and pipes will break, causing
scalding and leakage.
The tubes and pipes fitted on the product are inseparable parts of the Safe Care
technology, and shall not be removed by yourself. Otherwise, Haier shall not be liable for
any damages or injuries caused due to resulted potential risks.
If a drain hose is connected, it shall be
connected to sewage drain, avoiding
spilling the room.
Operation Instructions
Water heater automatically sets an energy saving temperature between 35 - 40
according to the difference between water temperature and ambient temperature
(normally this medium temperature can ensure small demand but not shower. For shower,
you need to quit Medium Warm mode, and press Mode button to enter Real-time Heating /
Keeping mode.Then the water can be heated to the setting temperature in a short time.).
When water temperature decreases to 34 , machine automatically restarts heating.
Heating power level can be manually set with Power button.
Example: Fig. 10 shows Medium Warm mode. Press Power button to set power level
2150 W with corresponding indication lighted. The actual temperature then is 52 . When
it decreases to 34 , machine will automatically re-heats to 40 and keeps warm. It cycles
in this way. In this mode, the machine defaulted highest heating temperature 40 can't be
adjusted.
(Fig.10)
(Fig.11)
7. Night Power Setting
With machine powered on, as described in Item 10, consecutively press Mode button
until it enters Night Power operation mode (with Night Power indication on the display). If
you would use hot water in early morning, you may adjust operation mode to Night Power
mode. Machine will heat / warm in default period (0:00 on and 6:00 off). Heating power
level and highest temperature can be manually set. In this mode, you can press Set button
to calibrate clock time.
In addition, in regional power consumption regulations, night power price rate is lower
than in day, so Night Power mode will be easier and more economic.
Note: In selecting Night Power function, water heater clock shall be adjusted to local
time. Inaccurate clock will cause night period partly charged as day use. (Only for
regions with Peak and Valley Electricity Rates)
Example: With machine powered on, press Mode button to select Night Power mode.
When PC clock displays 00:00, machine automatically starts heating. It enters warm
status after reaching setting value and has thermostat control during 0:00 6:00. (see
Fig.11)
8. Intelligent Heating Function
Intelligent heating function means that the system can analyze, process and memorize
user's water use habits in one week, and accordingly heat water in advance automatically.
With machine powered on, consecutively press Mode button until it enters Intelligent
operation mode with intelligent indication lighted on. System automatically starts heating
in the first memorized heating time since then. Heating power and highest temperature
can be manually set.
In non-heating period, system remains standby with clock and intelligent indications
lighted on. After it reaches the heating temperature, the machine will start to heat
aotomatically. If you'd like to quit Intelligent Heating mode and enter another mode, you
can press any button on control panel to activate the interface (buttons on remote
controller inactive), and then press Mode button to shift modes.
Notes: 1. In any mode after powering on, Intelligent Heating function can memorize your
water use habits. If you bathe in a fixed period everyday several times a week (4 times or
more than 4 times), system will analyze and memorize your this habit and automatically
start heating in advance.
2. Only in Intelligent mode can Intelligent function be executed.
(Fig.12)
(Fig.13)
Never do that
Be sure to act as per instructions
Description of the Symbols