Filter
Top Products
SKU 93926 For technical questions, please call 1-800-444-3353 PAGE 2
OPERATING INSTRUCTIONS
9. WARNING! Avoid accidental electrical shock. Never staple into electrical wires, especially those which may be
hidden from view.
10. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contain
chemicals known (to the State of California) to cause cancer, birth defects, or other reproductive harm. Some examples of
these chemicals are: Lead from lead-based paints, crystalline silica from bricks, cement, and other masonry products,
arsenic and chromium from chemically treated lumber.
(California Health & Safety Code 25249.5, et seq.)
11. WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible
conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors
which cannot be built into this product, but must be supplied by the operator.
Part # Description
1 Left Steel Panel
2 Right Steel Panel
3 Upper Cushion
4 Lower Cushion
5 Rubber Trigger Bump Stopper
6 Magazine
7 Pusher
8 Trigger
9 Trigger Lever
10 Handle
11 Trigger Assembly
12 Front Cover
13 Adjustable Cover
14 Cap Cover
15 Compression Spring
16 Spring Base
17 Step Pin
18 Step Pin
19 Driver Blade
20 Compression Set
21 O-Ring (12)
22 Screw (M5)
23 Magazine Assembly
24 Gun Body
25 Step Pin
26 Mini-Socket
27 Screw (M4)
28 O-Ring (9)
29 Screw (M4x27mm)
30 E-Ring (10)
31 Step Pin (6x28mm)
32 E-Ring (7)
33 Step Pin (4.35x28mm)
34 Screw (M5x33mm)
35 Staples (Qty. 400)
Note: When loading staples or when clearing jammed staples, always keep your hands off the Handle (10).
1. To load the Tacking Gun, push the Pusher (7) inward first. Then press downward and pull out the Pusher (7) assembly.
(See Figure A.)
2. Load a strip of Staples (35) into the Magazine (6). (See Figure A.)
3. Slide in the Pusher (7), and push it upward to lock it in place. (See Figure A.)
4. To use the Tacking Gun, position the nose of the tool against the work surface to which a Staple (35) is to be fired. Hold
the Tacking Gun firmly with both hands and squeeze the tool’s Handle (10). Repeat this procedure to finish the work.
(See Figure A.)
5. To clear jammed Staples (35), turn the Tacking Gun sideways so that the nose of the tool is pointing away from yourself and
others. Carefully remove the Pusher
(7) and remove all Staples from the
Magazine (6). If necessary, use
needle nose pliers to remove a bent
Staple from the nose of the tool. Then
reload the Magazine with up to 80
Staples, and re-install the Pusher.
(See Figure A.)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
23
34
21
22
33
32
31
30
29
28
27
25
26
NOTE:
Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
FIGURE A
PUSHER (7)
MAGAZINE (6)
HANDLE (10)
NOSE
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDER-
TAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISKS AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS
TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.