Hobart Welding Products Plasma Cutter Welder User Manual


 
Litho in USA
DISTRIBUTED BY:
Power Source Stock No. Description Qty. Price
AirForce 625 #500 493* 208/230 VAC, 50/60 Hz, w/ ICE-40C 25 ft (7.6 m) Hand-Held Torch
UPC: #715959303507; Shipping Weight: 67.5 lb (30.6 kg); Carton Dimensions: 15 X 27-3/4 X 20-1/2 in; Pallet Qty: 6
Note: Shipping via UPS not recommended
AirForce 625 #500 494* 208/230 VAC, 50/60 Hz, w/ ICE-40C 50 ft (15.2 m) Hand-Held Torch
UPC: #715959303514; Shipping Weight: 63 lb (28.6 kg); Carton Dimensions: 15 X 27-3/4 X 20-1/2 in; Pallet Qty: 6
Note: Shipping via UPS not recommended
Accessories
Torch Consumables See above
Replacement Torch #195 110 25 ft (7.6 m) ICE-40C Hand-Held Torch
#195 111 50 ft (15.2 m) ICE-40C Hand-Held Torch
Full KVA Plug Kit #119 172 Field
Plasma Standoff Roller Guide #194 883
Plasma Circle-Cutting Guide #195 981
Suction/Magnetic Pivot Base #195 979
Motor Guard Air Filter #042 306
Replacement Filter Element #042 312 Box of Four
#30A Economy Running Gear #195 093
and Cord Wrap
Date: Total Quoted Price:
ORDERING INFORMATION AND SYSTEM CHECKLIST
TORCH CONSUMABLES (Order from Hobart Service Parts.)
ACCESSORIES
ICE-40C Replacement Torches
#195 110 25 ft (7.6 m) hand-held torch
#195 111 50 ft (15.2 m) hand-held torch
Full KVA Plug Kit #119 172
240 VAC, 50 amp plug
(NEMA 14-50P) to fit full KVA
receptacle with a minimum
of 8 KVA generator power.
Plasma Standoff Roller
Guide #194 883
Helps maintain recommended
standoff distance to maximize
cutting performance and
improve tip life.
Plasma Circle-Cutting
Guide #195 981
Cut straight lines or
circles up to 12 in
diameter with ease.
Suction/Magnetic Pivot Base #195 979
Add this to your cutting guide for convenient
attachment to all flat surfaces. The extended arm
accommodates holes up to 30 in diameter.
Motor Guard Air Filter #042 306
This filter is equipped with a
mounting bracket that allows
installation on the top, side, or
rear panel of most plasma cutters.
The filter is equipped with a 1/4 in NPT port to
match the fittings on most plasma systems; it
has a rated airflow of over 45 SCFM.
#30A Economy Running
Gear and Cord Wrap
#195 093
Economical running gear
with angle for easy front
panel access provides
storage for gloves and tools.
Standard
Cutting
Extended
Cutting
Gouging
Deflector
#177 888
Retaining Cup
#192 050
Gouge Shield
#192 203
Retaining Cup
#192 050
Standard
Electrode
#192 047
Gouge Tip
#204 332R
Drag Shield
#204 323R
Retaining Cup
#192 050
Extended
35A Tip
#192 052R
Extended
Electrode
#192 048
Standard Tip
#204 325R
Standard
Electrode
#192 047
O-Ring
#169 232
1/8 in (3 mm)
stand-off
recommended
Swirl Ring
#192 049
For extended tip use, set
amperage control to 35 A.
Apply very light coating
of silicone grease (#169 231)
before installing.
For best gouging results,
set machine air pressure
at 55 PSI.
CUTTING PERFORMANCE
The cutting speed curve shows the
recommended maximum cutting speed
capabilities of the power source and torch
for the mild steel of various thickness.
The best cut quality is achieved by cutting
near the chart line. Cutting below the line
(too slow) will result in excess dross.
Cutting above the line (too fast) will cause
blowback and lack of penetration.
CUT SPEED CHART
0
50
100
150
200
250
300
350
400
16GA
(0.060)
1/8 1/4 3/8 5/8
MILD STEEL THICKNESS (IN)
CUT SPEED (IN/MIN)
*
®
Certified by Canadian Standards
Association to both Canadian
and U.S. standards.
NRTL/C