Filter
Top Products
6
English
3. Regulating the guide (Fig. 4)
The cutting position can be regulated by moving
the guide to the left or right after loosening its
wing-bolt. The guide may be mounted on either the
right or left side of the base.
CUTTING PROCEDURES
CAUTION
⅜ During use, when the body is out of condition or there
is unusual sound, please turn off a switch immediately.
⅜ During cutting, please do not pry the body or do not
push too much strongly. Please carry forward the
body calmly straightly.
It becomes the cause of an injury in response to
restitution. Moreover, while unreasonableness starts
a motor part, the life of saw blade is shortened.
⅜ Please do not carry out usage which made saw blade
facing up and sideways.
It becomes the cause of an injury.
⅜ Please use protection glasses.
⅜ Please use the protection implement of an ear.
⅜ Surely, the time of work discontinuation and after
work should turn off and put a switch, and should
pull out a lump plug from a power supply wall socket.
⅜ Be careful by rotating saw blade not to cut a code.
NOTE
⅜ Before beginning cutting, rotation of saw blade should
become the maximum high speed.
⅜ Extrusion fabrication cement building materials
should not cut 1 time of the cut depth with the speed
of 40 cm or less in 20 mm or less and 1 minute.
When using the cut depth, making it shallow, in order
that edge of a blade may open, dust-collecting power
declines.
1. The body (base) is carried on work piece and guide
slot of the base front part is united with a premarked
line.
When you do not incline, please follow large guide
slot as a guide, and when you incline (45°), follow
small guide slot as a guide (Fig. 5, Fig. 6, Fig. 7).
2. Saw blade turns on a switch in the state where work
piece cannot be touched.
This state is maintained until it carries forward the
body ahead slowly and finishes cutting it then.
For pulling and cleaning the skin, it advances straightly
with fixed speed.
MOUNTING AND DISMOUNTING THE SAW
BLADE
As for this body, saw blade is not attached to the body at
the time of factory shipments.
Please carry out attachment and removal of saw blade in
the following procedure in the case of use.
CAUTION
⅜ Surely, please turn off and put a switch in the case of
attachment and removal of saw blade, and pull out a
lump plug from a power supply wall socket.
It becomes the basis of the unexpected accident.
⅜ Attachment and detachment of a hexagonal flange
bolt should work with an attached box spanner.
If tools other than attachment are used, it will become
past [a bundle] and the shortage of bolting, and will
become the cause of an injury.
1. How to attach (Fig. 8)
(1) The cut depth is made into the minimum.
A lever is loosened, a base is made into the minimum
cut depth, and a lever is fastened.
(2) Two projection parts of a slide cover are pressed
down with a finger, and it moves up (Fig. 9).
(3) A washer (A) is removed (Fig. 10).
Pushing in a lock lever, a hexagonal flange bolt is
loosened with an attached box spanner, and a washer
(A) is removed.
Since a hexagonal flange bolt is a left screw, it will
loosen, if it turns clockwise.
After removing, the garbage adhering to the spindle
or the washer (A) is often wiped off.
(4) Saw blade is attached (Fig. 11)
A lower guard is carried out to full open, and saw
blade is attached.
It is made in agreement [the direction of an arrow of
saw blade] with the direction of an arrow of saw
cover.
(5) A hexagonal flange bolt is tightened (Fig. 12).
A washer (A) and a hexagonal flange bolt are attached
in order of the left figure, and a hexagonal flange bolt
is fully bound tight using an attached box spanner,
pushing a lock lever.
USE OF DUST BAG
CAUTION
⅜ To avoid serious accident, ensure the switch is
in the OFF position, and disconnect the plug from
the receptacle.
⅜ Never attempt to saw any material like metal and
so on that give off sparks. Such action can lead
to fire or injury.
1. Mounting the dust bag
Hold the clasp of the dust bag and insert it into
the adapting mouth of the body while opening the
thrusting mouth (Fig. 13).
2. Dumping sawdust and cleaning the inside of dust
bag
NOTE
⅜ If too much sawdust is accumulated inside the
dust bag, the dust collector will run low on
power. Attempt to dump the sawdust as early
as you can and clean the dust bag thoroughly
so that you can enjoy your work with strong dust
collecting power.
(1) Hold the clasp, open the thrusting mouth of the
dust bag, and pull it off from the body.
(2) Open the fastener (Fig. 14) and dump the sawdust.
MAINTENANCE AND INSPECTION
1. Inspecting the saw blade
Since use of a dull saw blade will degrade efficiency
and cause possible motor malfunction. Resharpen and
replace the saw blade as soon as abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.
01Eng_C5YC_ChT.P65E 10/18/06, 11:58 AM6