Filter
Top Products
28
English
HOUSING THE HEXAGONAL BAR WRENCH
It is possible to house the hexagonal bar wrench on the
base. (See Fig. 16)
CONNECTING WITH CLEANER
By connecting with cleaner (sold separately) through dust
collector and adapter (sold separately), most of dust can
be collected.
(1) Remove the hexagonal bar wrench from the base.
(2) Move the base fully forward. (Fig. 9, 10)
(3) Attach the chip cover with the shutter put between
the chip cover and gear cover. (Fig. 17)
(4) Connect the dust collector with adapter. (Fig. 18)
(5) Connect the adapter with the nose of cleaner. (Fig.
18)
(6) Insert dust collector into the rear hole or the base
until the hook catches in the notch. (Fig. 19)
(7) Press the hook to remove the dust collector.
MAINTENANCE AND INSPECTION
1. Inspecting the blade
Continued use of a dull or damaged blade will
result in reduced cutting efficiency and may cause
overloading of the motor. Replace the blade with
a new one as soon as excessive abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the
power tool.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
Table 1 List of appropriate blades
Material
Blade
No. 1 No. 1
No.11
No. 12,
No. 15
No. 16,
No. 21 No. 22 No. 41 No. 97 123X
to be cut
(Long)
(Super Long)
42 46
Material quality Thickness of material (mm)
Lumber
General lumber
Below Below 10 ∼ Below 10 ∼ 5 ∼ 10 ∼
105 135 55 20 55 40 65
Plywood
5 ∼ Below 5 ∼ 3 ∼
30 10 30 20
Iron plate
Mild steel plate
3 ∼ Below 2 ∼ 1.5 ∼
63 510
Stainless steel plate
1.5 ∼
2.5
Nonferrous
Aluminium copper, 3 ∼ Below Below
metal
brass 12 3 5
Aluminium sash
Height Height Height
up to up to up to
25 25 30
Plastics
Phenol resin, melamin, 5 ∼ Below 5 ∼ Below 5 ∼
resin, etc. 20 6 15 6 15
Vinyl chloride, 5 ∼ Below 5 ∼ Below 5 ∼ 3 ∼ 5 ∼
acryl resin, etc. 30 10 20 5 30 20 15
Foamed polyethylene, 10 ∼ 3 ∼ 5 ∼ 3 ∼ 10 ∼ 3 ∼ 5 ∼
foamed styrol 55 25 25 25 55 40 25
Pulp
Card board, 10 ∼ 3 ∼ 10 ∼ 3 ∼
corrugated paper 55 25 55 40
Hardboard
3 ∼ Below 3 ∼
25 6 25
Fiberboard
Below
6
NOTE:
⅜ The minimum cutting radius of No. 1 (Long), No.1 (Super Long), No. 21, No. 22 and No. 41 blades is 100 mm.
⅜ No. 1 (Long), No.1 (Super Long), No. 11, No. 12, No. 15, No. 16, No. 21, No. 22 and No. 97 blades are
sold separately.