Filter
Top Products
16574014_ed1 3
CA Angle Air Grinder, Die Grinder and Sander Parts List
Item Part Description Part Number Item Part Description Part
Number
Common parts for ALL CA Grinders 22 Angle Housing Assembly LA1-A550S
1 Inlet Assembly LG1-A465A 23 Clamp Spacer LA1-46
2 Inlet Screen R1602-61 24 Clamp Nut LG1-27
• 3 Inlet Seal 85H-167 25 Grease Fitting D0F9-879
Throttle Valve Cartridge Kit LG1-K300 26 Upper Arbor Bearing AG210-693
4 Throttle Valve Cartridge Case LG1-300A ¤ 27 Wick
4A Throttle Valve Seat LG1-303 for CA120 LA1-560
4B Throttle Valve AG210-302 for CA200 LA1-561
4C Throttle Valve Spring 7L-51 28 Bevel Gear Nut AG210-578A
4D Throttle Valve Spring Seat LG1-592 29 Lower Arbor Bearing AG210-24
5 Motor Housing LG1-40 30 Arbor Bearing Cap AG210-531
6 Throttle Lever LG1-273 31 Arbor
6A Locking Throttle Lever Assembly
(for models ending in L, C, ML or MC)
LG1-A400 for all models ending in
G4, G4C or G4L
AG210-4-G4
* Lever Lock LG1-402 for all models ending in
S4, S4C or S4L
AG210-4-W2
* Lock Spring LG1-405
* Lock Pin 5UT-757 for all models ending in
P63, P63C or P63L
LA1-6
7 Throttle Lever Pin 61H-120
8 Throttle Valve Plunger LG1-191 H63, H63C or H63L LA1-103-1
9 Rear Rotor Bearing DG230-22 * Warning Label
• 10 Rear Rotor Bearing Spacer (2) DG20-278 for models ending in P63-EU EU-63--99
• 11 Rear Rotor Bearing Retainer LG1-118 for all other models ending in-EU EU-99
12 Rotor for all other models LG1-99
for CA120 (5 vane slots) LG1-53-5 * Nameplate
for CA200 (3 vane slots) LG1-53-3 for CA120 models ending in-EU LA112-EU-301
• 13 Vane Packet (set of 5 Vanes) LG1-42-5 for all other CA120 models LA112-301
14 Front End Plate LG1-11 for CA200 models ending in-EU LA120-EU-301
15 Front End Plate Spacer DG10-65-5 for all other CA200 models LA120-301
• 16 Front Seal Cup LG1-32 Additional parts for all collet
models
17 Front Rotor Bearing LG1-24
18 Flow Ring 32 Collet
for CA120 (12000 rpm) (brown) LG1-103-1 for models ending in-EU DG110-700-
for CA200 (20000 rpm) (red) LG1-103-3 6mm
19 High Profile Flange LG1-23 for all other models DG110-700-
# 19A Low Profile Concentric Flange
(for all models ending in C)
LG1R-23 G4
33 Nosepiece AG210-698A
20 Flange Clamp LG1-29 34 Collet Nut AG210-699A
21 Bevel Pinion and Bevel Gear
(sold only as a matched set)
for CA120 LA1-A552-2.0S
for CA200 LA1-A552-1.5A
* Not illustrated.
• To keep downtime to a minimum, it is desirable to have on hand certain repair parts. We recommend that you stock one
(pair or set) of each part indicated by a bullet (•) for every four tools in service.
¤ The LA1-A550S Angle Housing Assembly is furnished with two Wicks. Use Wick (LA1-561) with the notch on CA200 models.
WARNING
# Always install a Locking Throttle Lever Assembly (6A) on a tool with a Low Profile Concentric Flange (19A). Do not
equip a tool with a standard non-locking Throttle Lever (6) and Low Profile Concentric Flange. This can allow the tool to
continue to run if dropped or set down.