Filter
Top Products
6 16573313_ed3
99V Series Air Grinder Parts List
Use This Part Listing With Drawing TPA717-3 For Models With Built-in Oilers
Item Part Description Part Number Item Part Description Part Number
‡ 1 Cylinder Case Assembly
*
Nameplate Screw
BN403-302
2 Throttle Valve Assembly 99V60-A302 (for European compliant models) (4)
† 3 Small Seal AFH120A-358
*
Warning Label
EU-99
† 4 Large Seal C321-606 (for European compliant models)
† • 5
Inlet Bushing 88V60-38
*
Nameplate Kit (for domestic models) 99V-K301A
5A Inlet Bushing Screen 834-61 Nameplate Screw (4) BN403-302
• 6 Throttle Valve Spring 99V60-262 Warning Label WARNING-4-99
7 Throttle Valve Seat Support Assembly 99V60-A303 † 21 Oiler Chamber Plug Washer R3-92A
† • 8 Air Strainer Screen 99V60-61 22 Oiler Chamber Plug 231-665
9 Valve Seat Cap R4-157 23 Oiler Assembly 99V60-A198
† • 10 Valve Seat R4-159A † 24 Oiler Felt (2) R1-75
11 Valve Seat Washer 99V60-155
25
Oiler Adjusting Screw R1-71A
12 Valve Seat Lock Washer H54U-352 † 26 Oiler Body Seal HRA20A-117
13 Valve Seat Screw 99V60-83 27 Dead Handle 99V60-48
• 14 Throttle Lever Pin MR-100 28 Dead Handle Screw 99V60-634
15 Locking Lever Assembly 99V60-A400A 29 Arbor
16 Lever Lock 88V60-402 for 99V45 (Orange) 99V45-204-P10
17 Lever Lock Spring 88V60-405 for 99V60 (Blue) 99V60-204-P10
18 Lever Lock Pin 502B-120 for 99V77 (Green) 99V77-204-P10
18A
Exhaust Diuser
99V77-123
for 99V85 (Red) 99V85-204-P10
(not used on 99V45 or 99V60) 30 Front Rotor Bearing R380-105
19 Exhaust Deector 99V60-23 31 Front End Plate 99V60-11
20 Exhaust Deector Screw (3) 99V60-200
*
Nameplate Kit
99V-EU-K301A
(for European compliant models)
* Not Illustrated.
• To keep downtime to a minimum, it is desirable to have on hand certain repair parts. We recommend that you stock one (pair or set) of each
part indicated by a bullet (•) for every four tools in service.
‡ Whenever a new Cylinder Case Assembly is installed, select the correct Nameplate from the Nameplate Kit and attach it to the Cylinder Case
with the Nameplate Screws.
† Indicates Tune-up Kit part.
Use this part listing for all models
Item Part Description Part Number Item Part Description Part Number
• 33 Rotor Key R43F-70 47 Motor Clamp Belleville Washer (2) 99V60-207
34 Rotor 99V60-53 †• 48 Cylinder Case Gasket 99V60-283
† • 35 Vane Packet (set of 4 Vanes) 99V60-42-4 49 Cup Wheel Guard
36 Cylinder Assembly 99V60-A3 for 5” or 6” Cup Wheels 99V60-A216A
37
End Plate Dowel 5040-6 for 130 or 150 mm Cup Wheels 99V60-A216MA
38 Cylinder Dowel 502B-120 50 Depressed Center Wheel Guard for Type 27
39 Exhaust Silencer 99V60-311 or Type 28 Wheels
40 Rear End Plate 99V60-A12 for 9” or 230 mm 99V60-106-9
† • 41 Rear End Plate Gasket 99V60-739 for 7” or 180 mm 99V77-106-7
42
Controller Assembly (consists of Controller
50A
Saucer Wheel Guard (for 7” diameter x 1”
99V60-206-7
and Rotor Bearing Seal Assembly) thick x 1-5/8” over all height Saucer Wheel)
for 99V45 (4500 rpm) (Orange) 99V45-A524
51
Cylinder Case Screw Lock Washer (4) 10BM-67
for 99V60 (6000 rpm) (Blue) 99V60-A524 52 Cylinder Case Screw (4) 99V60-638
for 99V77 (7700 rpm) (Green) 99V77-A524 53 Autobalancer Assembly 99V60-A713
for 99V85 (8500 rpm) (Red) 99V85-A524 54 Autobalancer Wrench (7/8” single-end;
88V60-169
43
Rotor Bearing Seal Assembly (consists
99V60-A28A
open-end wrench)
of Rear Rotor Bearing and Rotor 56 Wheel Retaining Screw
Bearing Seal) for all Type 27 and
99V60-219
45 Rotor Bearing Cage 99V60-107A Type 28 Wheels
46 Controller Retaining Nut for 7” diameter x 1” thick x 1-5/8”
99V60-119
for 99V45 and 99V85 R4-120 overall height Saucer Wheels
for all others G8-120A
• To keep downtime to a minimum, it is desirable to have on hand certain repair parts. We recommend that you stock one (pair or set) of each
part indicated by a bullet (•) for every four tools in service.
† Indicates Tune-up Kit part.