Filter
Top Products
• Lock the pivoting shoe in place by tightening the two pivoting shoe hex screws.
• Pull outward on the pivoting shoe to ensure it is firmly in place.
OOPPEERRAATTIINNGG TTHHEE RREECCIIPPRROOCCAATTIINNGG SSAAWW
NNeevveerr ttaappee tthhee ttrriiggggeerr sswwiittcchh ddoowwnn ttoo pprroovviiddee ccoonnttiinnuuoouuss
hhiigghh ssppeeeedd.
.
The tool may fail under such conditions causing fire or personal
injury.
VVAARRIIAABBLLEE SSPPEEEEDD CCOONNTTRROOLL WWHHEEEELL
The variable speed control wheel controls the
speed at which the saw will run. To set the speed
control at the slowest speed, rotate the speed control
wheel toward MIN on the dial. To set the speed
control at the fastest speed, rotate the speed control
wheel backward to MAX. To select intermediate
speeds, rotate the speed control to an appropriate
position between MAX and MIN on the speed control
wheel.
TTRRIIGGGGEERR SSWWIITTCCHH
To turn the saw ON squeeze the trigger switch.
NNOOTTEE::
The saw will run at the speed selected on the speed control wheel.
To turn the saw OFF, release the trigger switch.
GGEENNEERRAALL CCUUTTTTIINNGG
AAllwwaayyss hhoolldd tthhee ssaaww iinn ffrroonntt ooff yyoouu aanndd aawwaayy ffrroomm yyoouurr bbooddyy.. KKeeeepp yyoouurr
hhaannddss aanndd ffeee
ett wweellll aawwaayy ffrroomm tthhee wwoorrkk ppiieeccee..
NNeevveerr ffeeeedd tthhee bbllaaddee iinnttoo tthhee wwoorrkk ppiieeccee uunnttiill tthhee bbllaaddee iiss aatt ffuul
lll ssppeeeedd..
IIff tthhee bbllaaddee iiss nnoott aatt ffuullll ssppeeeedd,, tthhee ssaaww mmaayy kkiicckk bbaacckk ccaauussiinngg sseerriioouuss
ppeerrssoonnaall iinnjjuurryy.
.
UUssee pprrooppeerr bbllaaddee ffoorr tthhee ppaarrttiiccuullaarr ccuuttttiinngg aapppplliiccaattiioonn..
DDoo nnoott ffoorrccee tthhee ssaaww.. EExxcceessssiivvee ffoorrccee mmaay
y rreessuulltt iinn aa
bbrrookkeenn bbllaaddee..
Use only enough pressure to keep the saw moving through the
work piece.
• Put on eye protection.
• Clear the saw of any
foreign material.
• Make sure the work piece is
held securely in place. Hold
smaller pieces in a vise or
attach to the workbench
with clamps.
• Mark out the line to be cut
so it is easily visible.
• Pull the trigger to start the
saw.
• Set the shoe against the work piece.
• When the blade reaches full speed, slowly feed the blade into the work piece.
PPLLUUNNGGEE CCUUTTTTIINNGG
NNeevveerr ffeeeedd tthhee bbllaaddee iinnttoo tthhee wwoorrkk ppiieeccee uunnttiill tthhee bbllaaddee
iiss aatt ffuullll ssppeeeedd.. IIff tthhee bblla
addee iiss nnoott aatt ffuullll ssppeeeedd,, tthhee ssaaww mmaayy kkiicckk bbaacckk
ccaauussiinngg sseerriioouuss ppeerrssoonnaall iinnjjuurryy..
1211
TRIGGER SWITCH
SPEED CONTROL WHEEL