Filter
Top Products
RREEMMOOVVIINNGG // AATTTTAACCHHIINNGG BBAATTTTEERRYY PPAACCKK
RREEMMOOVVEE BBAATTTTEERRYY PPAACCKK::
1. Press both release buttons on
either side of the Impact Wrench to
release the battery pack.
2. Pull battery pack free of Impact
Wrench.
AATTTTAACCHH BBAATTTTEERRYY PPAACCKK::
1. Align the raised portion of the bat-
tery pack with the groove in the
battery compartment of the Impact
Wrench.
2. Press the battery pack into place.
Make sure the latches are securely
fastened. Do not use the Impact
Wrench if the battery pack is not
seated properly.
CCHHAARRGGEERR
BBeeffoorree uussiinngg bbaatttteerryy cchhaarrggeerr,, pplleeaassee rreeaadd ccaarreeffuullllyy aallll
iinnssttrruuccttiioonnss aanndd ccaauuttiioonnaarryy mmaarrkkiinnggss oonn bbaatttte
erryy cchhaarrggeerr,, bbaatttteerryy ppaacckk aanndd
pprroodduucctt uussiinngg bbaatttteerryy..
TThhee cchhaarrggeerr wwiillll nnoott aauuttoommaattiiccaallllyy ttuurrnn ““OOFFFF”” wwh
heenn tthhee
bbaatttteerryy ppaacckk iiss ffuullllyy cchhaarrggeedd..
The charging indicator light will remain
““OONN””
until the charger is disconnected from the electrical outlet.
UUssee oonnllyy tthhee cchhaarrggeerr wwhhiicchh aaccccoommppaanniieedd yyoouurr pprroodduucctt oorr
ddiirreecctt rreeppllaacceemmeenntt aass
lliisstteedd iinn tthhiiss mmaannuuaall..
Do not substitute any other charger. Use only Alltrade
approved chargers with your product.
DDoo nnoott ddiissaasssseemmbbllee cchhaarrggeerr..
DDoo nnoott uussee cchhaarrggeerr iiff iit
t hhaass bbeeeenn ddaammaaggeedd,, lleefftt oouuttddoooorrss iinn tthhee rraaiinn,, ssnnooww,, wweett
oorr ddaammpp eennvviirroonnmmeennttss,, oorr iimmmmeerrsseedd iinn lliiqquuiidd.
.
TThhee bbaatttteerryy ppaacckk aanndd cchhaarrggeerr hheeaatt dduurriinngg cchhaarrggiinngg..
Place the charger on a flat,
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
WWhheenn tthhee bbaatttteerryy ppaacckk rreeqquuiirreess rreecchhaarrggiinngg,, aa
33--55 hhoouurr cchhaarrggee aalllloowwss tthhee ttooooll ttoo
ooppeerraattee aatt ffuullll ppoowweerr..
A charging indicator light on the charger will illuminate to
show that charging is taking place.
CCHHAARRGGIINNGG BBAATTTTEERRYY PPAACCKK
CCHHAARRGGEE BBAATTTTEERRYY PPAACCKK::
1.Make sure the trigger on
the Cordless Impact
Wrench is in the
““OOFFFF””
position and remove the
battery pack from the
Impact Wrench.
2.Insert the battery pack into the
charger. Be sure that the battery
pack is fully seated in the charg-
er. Do not force.
3.Plug the charger into the nearest
120 volt, electrical outlet. The
indicator light will come
““OONN””
.
IIMMPPOORRTTAANNTT IINNFFOORRMMAATTIIOONN FFOORR RREECCHHAARRGGIINNGG HHOOTT BBAATTTTEERRIIEESS
When using your Cordless Impact Wrench continuously, the batteries in your bat-
tery pack will become hot. You should let a hot battery pack cool down for approx-
imately 30 minutes before attempting to recharge. When the battery pack becomes
discharged and is hot, the red light on the charger will flash. When the battery pack
cools down, the red light will glow continuously.
TThhiiss wwi
illll ooccccuurr wwhheenn ccoonnttiinnuuoouuss uussee ooff yyoouurr CCoorrddlleessss
IImmppaacctt WWrreenncchh ccaauusseess tthhee bbaatttteerryy ppaacckk ttoo bbeeccoommee hhoott..
It does not occur
under normal circumstances.
AASSSSEEMMBBLLYY
BBee aawwaarree tthhaatt tthhiiss ttooooll iiss aallwwaayyss iinn aann ooppeerraattiinngg ccoonnddii--
ttiioonn bbeeccaauussee iitt ddooeess nnoott hhaavvee ttoo bbee pplluuggggeedd
iinnttoo aann eelleeccttrriiccaall oouuttlleett..
Always
turn the switch
““OOFFFF””
and remove the battery pack before changing bits.
12
RELEASE
BUTTON
BATTERY PACK
LED LIGHT
BATTERY
CHARGER
120V AC
ADAPTER