Filter
Top Products
AATTTTAACCHHIINNGG TTHHEE BBLLAADDEE
AAllwwaayyss rreemmoovvee bbaatttteerryy ppaacckk bbeeffoorree iinnssttaalllliinngg oorr rreemmoovviinngg bbllaaddee..
WWhheenn rreemmoovviinngg tthhee bbllaaddee ffrroomm tthhee ttooool
l,, aavvooiidd ccoonnttaacctt wwiitthh sskkiinn aanndd uussee
pprrooppeerr pprrootteeccttiivvee gglloovveess wwhheenn ggrraassppiinngg tthhee bbllaaddee oorr aacccceessssoorryy..
Accessories
may be hot after prolonged use.
1. Loosen the two screws
on the blade holder
by turning them count-
er-clockwise. Push the
blade shank into the saw
blade holder as far
as it will go. Make sure
that the blade’s teeth
are facing forward.
2. Tighten the screws slowly, first one
side, then the other, until the blade
reaches the desired position.
Tighten the screws completely to
hold the blade in place.
OOPPEERRAATTIINNGG TTHHEE JJIIGGSSAAWW
NNeevveerr ttaappee tthhee ttrriiggggeerr sswwiittcchh ddoowwnn ttoo pprroovviiddee ccoonnttiinnuuoouuss
hhiigghh ssppeeeedd..
The tool may fail under such conditions causing fire or personal
injury.
14
TThhee bbaatttteerryy ppaacckk aanndd cchhaarrggeerr hheeaatt dduurriinngg cchhaarrggiinngg..
Place the charger on a flat,
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
WWhheenn tthhee bbaatttteerryy ppaacckk rreeqquuiirreess rreecchhaarrggiinngg,, aa 1
1 hhoouurr cchhaarrggee aalllloowwss tthhee ttooooll ttoo
ooppeerraattee aatt ffuullll ppoowweerr..
A charging indicator light on the charger will illuminate to
show that charging is taking place.
CCHHAARRGGIINNGG BBAATTTTEERRYY PPAACCKK UUSSIINNGG OONNEE HHOOUURR CCHHAARRGGEERR ##669900550077
CCHHAARRGGEE BBAATTTTEERRYY PPAACCKK::
1. Plug the charger into the
nearest 120 volt electrical
outlet. The step of the bat-
tery has positive and nega-
tive terminal markings on it.
Align the markings with the
identical markings on the
top of the charger base.
Insert the battery pack into
base. Pack will not insert
properly if reversed.
2. Make sure the trigger on the
Cordless Jigsaw is in the
““OOFFFF””
position and remove the battery pack from the Cordless Jigsaw.
3. If, when first inserting the battery pack, the red
““OONN””
button does not light up,
press the “SET” button on the charger. When the battery is charging, the red
light is
““OONN””
.
4. After approximately one hour of charging, the red indicator light should go
““OOFFFF””
and the green light should come
““OONN””
. The green light indicates that the
battery is fully charged.
5. When fully charged, reattach battery pack onto Cordless Jigsaw, making certain
latches fasten securely. Cordless Jigsaw will not operate properly if the battery
pack is not seated properly.
AASSSSEEMMBBLLYY
BBee aawwaarree tthhaatt tthhiiss ttooooll iiss aallwwaayyss iinn aann ooppeerraattiinngg ccoonnddiittiioonn
bbeeccaauussee iitt ddooeess nnoott hhaavvee ttoo bbee pplluuggggeedd iin
nttoo aann eelleeccttrriiccaall oouuttlleett..
Always turn
the switch
““OOFFFF””
and remove the battery pack before changing blades.
LOOSEN
TIGHTEN
13
BATTERY
CHARGER
BATTERY PACK