Filter
Top Products
FFOORRWWAARRDD//RREEVVEERRSSEE AANNDD TTRRIIGGGGEERR LLOOCCKK LLEEVVEERR
BBee ssuurree tthhee ttrriiggggeerr iiss rreelleeaasseedd wwhheenn cchhaannggiinngg tthhee ppoossiittiioonn ooff tthhee lleevveerr..
Always store the tool in the
““LLOOCCKKEEDD//OOFFFF””
position.
AAllwwaayyss cchheecckk
tthhee ddiirreeccttiioonn ooff tthhee CCoorrddlleessss DDrriillll''ss rroottaattiioonn bbeeffoorree uussee..
TTOO SSEELLEECCTT TTHHEE DDIIRREECCTTIIOONNSS
OOFF RROOTTAATTIIOONN::
• To select forward Cordless Drill
rotation, press the trigger lock
from left to right flat against the Cordless
Drill body.
• To select reverse, press the trigger lock lever
in the opposite direction.
• The center position locks the tool.
TTOORRQQUUEE SSEETTTTIINNGGSS
TToo pprreevveenntt ddaammaaggiinngg tthhee ttooooll oorr ddrriivviinngg ssccrreeww ttoooo ddeeeepp
iinnttoo wwoorrkk ppiieeccee,, rreelleeaassee tthhee ttrriiggggeerr wwhheenn yyoouu
ffeeeell tthhee cclluuttcchh sslliipp..
TTHHEE CCOONNTTRROOLL RRIINNGG AADDJJUUSSTTSS TTHHEE LLEEVVEELL OOFF TTOORRQQUUEE::
• For light duty work, use lower settings.
• For heavy duty work, use higher settings.
PPRROOPPEERR SSEETTTTIINNGG FFOORR DDRRIIVVIINNGG SSCCR
REEWWSS::
1. Set the ring on the lowest
setting to begin.
2. Try tightening the first screw.
If the drill drives smoothly,
proceed with the next screw.
3. If the Drill’s clutch slips,
increase the torque setting
and try again until the Drill
drives the screw without incident.
14
1. Hold the rear end of the chuck
in one hand and use the other
hand to rotate the front end in a
counterclockwise direction to
open the jaws of the chuck.
2. Insert the shank of the bit (or
other accessory) fully into the
keyless chuck, taking care to
keep the bit in the center of
the jaws of the chuck.
3. Turn the front end of the chuck clockwise to hold the bit in place.
4. Tighten securely by turning the front end of the chuck clockwise while holding
the rear end.
OOPPEERRAATTIINNGG TTHHEE DDRRIILLLL
NNeevveerr ttaappee tthhee ttrriiggggeerr sswwiittcchh ddoowwnn ttoo pprroovviiddee ccoonnttiinnuu--
oouuss hhiigghh ssppeeeedd..
The tool may fail under such conditions causing fire or
personal injury.
VVAARRIIAABBLLEE SSPPEEEEDD TTRRIIGGGGEERR SSWWIITTCCHH
TTHHIISS TTOOOOLL IISS CCOONNTTRROOLLLLEEDD
BBYY AA TTRRIIGGGGEERR SSWWIITTCCHH::
• The speed of the Cordless Drill depends
on the amount of pressure you put on the
trigger.
• The more pressure you apply, the faster
the Cordless Drill will go.
• Release the pressure and the Cordless Drill
will slow down.
13
TIGHTEN
LOOSEN
HOLD
TRIGGER
LOCK
TRIGGER
SWITCH
CONTROL RING