Filter
Top Products
FFUUNNCCTTIIOONNAALL DDEESSCCRRIIPPTTIIOONN
CCOONNTTRROOLLSS AANNDD CCOOMMPPOONNEENNTTSS::
1. Trigger Switch
2. Lock-On Switch
3. Direction Control Lever
4. Comfort Rubber Grip
5. Motor Housing
OOPPEERRAATTIINNGG IINNSSTTRRUUCCTTIIOONNSS
DDiissccoonnnneecctt tthhee ppoowweerr pplluugg ffrroomm tthhee AACC ppoowweerr ssoouurrccee
bbeeffoorree aannyy aasssseemmbbllyy,, aaddjjuussttmmeennttss,, oorr aaddddiinngg//rreemmoovvi
inngg aacccceessssoorriieess..
Following this preventative step reduces the risk of the drill coming on acciden-
tally and the risk of damage to the workpiece and injury to the operator.
8
7
TToo pprreevveenntt aacccciiddeennttaall ssttaarrttiinngg,, aallwwaayyss ddiissccoonnnneecctt tthhee pplluugg ffrroomm tthhee ppoowweerr
ssoouurrccee bbeeffoorree mmaakkiinngg aannyy a
addjjuussttmmeennttss oorr cchhaannggiinngg aacccceessssoorriieess..
NNeevveerr rruunn tthhee ddrriillll wwhhiillee ccaarrrryyiinngg iitt aatt yyoouurr ssiiddee..
IIff tthhee bbiitt
bbeeccoommeess bboouunndd iinn tthhee wwoorrkk ppiieeccee,, rreelleeaassee tthhee ttrriiggggeerr iimmmmeeddiiaatteellyy
aanndd pprreeppaarree ffoorr tthhee ttooooll ttoo kkiicckkbbaac
ckk ttoowwaarrdd yyoouu..
Reverse the direction of rota-
tion, then back out the bit by slowly squeezing the trigger.
MMaakkee ssuurree aallll aacccceessssoorriieess aarree rraatteedd ffoorr tthhee rreeccoommmmeennddeedd ssppeeeedd ooff tthhee ddrriillll..
Brushes, grinding wheels and other accessories may fall apart if run at too high
a speed, sending dangerous debris flying at the operator.
UUssee gglloovveess wwhheenn cchhaannggiinngg hhoott bbiittss aanndd aacccceessssoorriieess ttoo aavvooiidd bbuurrnnss..
SSYYMMBBOOLLSS
IIMMPPOORRTTAANNTT::
Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
SSYYMMBBOOLL NNAAMMEE EEXXPPLLAANNAATTIIOONN
V Volts Voltage (Potential)
A Amperes Current
Hz Hertz Frequency (Cycles per Second)
W Watt Power
Kg Kilograms Weight
Alternating Current Type of Current
Direct Current Type of Current
Alternating or Direct Current Type of Current
Earthing Terminal Grounding Terminal
Class II Construction Denotes Double Insulation
min Minutes Time
s Seconds Time
Diameter Size of Drill Bits,
Grinding Wheels, etc.
No load speed No-load Rotational Speed
.../min Revolutions per Minute Revolutions, Surface Speed,
Strokes, etc. per Minute
1,2,3, … Ring Selector Settings Speed, Torque or Position Settings
2
4
6
3
9
5
7
1
8
6. Motor Brush (2)
7. Double Insulated Power Cord
8. Chuck
9. Chuck Key