Filter
Top Products
4
ENGLISH
Explanation of general view
1 Battery cartridge
2Button
3 Charging light
4 Battery charger
5 Switch trigger
6 Reversing switch lever
7 Clockwise
8 Counterclockwise
9 Speed change lever
10 Action mode change lever
11 Lock button
12 Adjusting ring
13 Graduations
14 Pointer
15 Sleeve
16 Ring
17 Bit
18 Bit holder
19 Screw
20 Set plate
21 Limit mark
22 Brush holder cap
23 Screwdriver
SPECIFICATIONS
Model 6207D 6217D 6317D 6337D 6347D
Capacities
Steel.....................................10 mm 10 mm 13 mm 13 mm 13 mm
Wood....................................25.4 mm 25.4 mm 25.4 mm 32 mm 38 mm
Wood screw..........................6 x 75 mm 6 x 75 mm 6 x 75 mm 6 x 75 mm 10 x 89 mm
Machine screw .....................13 mm 13 mm 13 mm 13 mm 13 mm
No load speed (min
-1
)
High......................................0 – 1,300 0 – 1,300 0 – 1,300 0 – 1,300 0 – 1,300
Low.......................................0 – 400 0 – 400 0 – 400 0 – 400 0 – 400
Overall length ............................233 mm 233 mm 243 mm 243 mm 243 mm
Net weight .................................1.7 kg 1.9 kg 2.0 kg 2.1 kg 2.4 kg
Rated voltage ............................D.C.9.6 V D.C.12 V D.C.12 V D.C.14.4 V D.C.18 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is used for drilling and screw driving in wood,
metal and plastic.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
ENC001-3
1. SAVE THESE INSTRUCTIONS- This manual con-
tains important safety and operating instruc-
tions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
3. CAUTION - To reduce risk of injury, charge only
MAKITA type rechargeable batteries. Other types
of batteries may burst causing personal injury
and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold
by the battery charger manufacturer may result
in a risk of fire, electric shock, or injury to per-
sons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when discon-
necting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
8. Do not operate charger with damaged cord or
plug - replace them immediately.
9. Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in
any way; take it to a qualified serviceman.
10. Do not disassemble charger or battery cartridge;
take it to a qualified serviceman when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
11. To reduce risk of electric shock, unplug charger
from outlet before attempting any maintenance
or cleaning. Turning off controls will not reduce
this risk.
12. The battery charger is not intended for use by
young children or infirm persons without super-
vision.
13. Young children should be supervised to ensure
that they do not play with the battery charger.
14. If operating time has become excessively
shorter, stop operating immediately. It may result
in a risk of overheating, possible burns and even
an explosion.
15. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
ADDITIONAL SAFETY RULES FOR CHARGER
& BATTERY CARTRIDGE
1. Do not charge battery cartridge when tempera-
ture is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
2. Do not attempt to use a step-up transformer, an
engine generator or DC power receptacle.
3. Do not allow anything to cover or clog the
charger vents.
4. Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.